Tutorials: Difference between revisions

From FreeCAD Documentation
(<gallery mode=packed> does not obstruct the image with the text. Every image should have a sentence that briefly describes the content of the tutorial.)
m (v0.17)
Line 88: Line 88:
<!--T:12-->
<!--T:12-->
FEM example01 pic00.jpg|link=[[FEM CalculiX Cantilever 3D]]|[[FEM CalculiX Cantilever 3D|CalculiX cantilever FEM analysis]] (v0.17) <br/>This in an example included in every installation of FreeCAD; it demonstrates a basic analysis with the CalculiX FE solver. Purge the current result, re-run the solver, and view the displacements and stresses in the deformed mesh in the viewport.
FEM example01 pic00.jpg|link=[[FEM CalculiX Cantilever 3D]]|[[FEM CalculiX Cantilever 3D|CalculiX cantilever FEM analysis]] (v0.17) <br/>This in an example included in every installation of FreeCAD; it demonstrates a basic analysis with the CalculiX FE solver. Purge the current result, re-run the solver, and view the displacements and stresses in the deformed mesh in the viewport.
FEM tutorial result.png|link=[[FEM tutorial]]|[[FEM tutorial|Simple FEM introduction]] (0.17) <br/>This is a short introduction to the steps required to perform an analysis in the FEM Workbench: model your object, create a mesh, add constraints and forces, add a material, run the solver, and visualize the results.
FEM tutorial result.png|link=[[FEM tutorial]]|[[FEM tutorial|Simple FEM introduction]] (v0.17) <br/>This is a short introduction to the steps required to perform an analysis in the FEM Workbench: model your object, create a mesh, add constraints and forces, add a material, run the solver, and visualize the results.
Figure 11 Deformed Mesh.png|link=[[FEM Shear of a Composite Block]]|[[FEM Shear of a Composite Block|FEM shear analysis of a composite block]] (v0.17) <br/>Study the deformation of a block made of a hard nucleus surrounded by a softer material: create mesh regions, add materials, set up sliding constraints, add shear loads, run the solver, and visualize the results with a clip plane.
Figure 11 Deformed Mesh.png|link=[[FEM Shear of a Composite Block]]|[[FEM Shear of a Composite Block|FEM shear analysis of a composite block]] (v0.17) <br/>Study the deformation of a block made of a hard nucleus surrounded by a softer material: create mesh regions, add materials, set up sliding constraints, add shear loads, run the solver, and visualize the results with a clip plane.
</translate>
</translate>

Revision as of 06:30, 8 April 2019

This page presents a selection of high quality written tutorials. A complete, unsorted list of tutorials can be found in Category:Tutorials.

Visit offsite tutorials and video tutorials for lists of tutorials hosted on external sites. A useful source of video tutorials is YouTube.

If you'd like to contribute with writing wiki documentation and tutorials, see the general wiki guidelines in WikiPages, and read the tutorial guidelines.

Please notice the version of FreeCAD used in the tutorial as some tutorials may use an old version of the program. Although the general modelling process may still work, some tools may have changed.

Architecture and BIM

Modeling Parts

FreeCAD provides two main workflows to modeling parts:

Please note that the PartDesign Workbench workflow was considerably changed from FreeCAD 0.17 onward; some of the tutorials haven't been updated and may refer to the 0.16 version.

Drafting and Sketching

Technical Drawings

FEM

CNC & 3D Printing

Import and Export

Rendering

Robot workbench

Plotting

Drawings

Development of the Drawing Workbench stopped in FreeCAD 0.16. Consider using the TechDraw Workbench instead.
List of Commands
Interface Customization