Translations:Arch Rebar/7/en: Difference between revisions

From FreeCAD Documentation
(Importing a new version from external source)
 
(Importing a new version from external source)
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
⚫
# Switch to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]]
# Create a [[Arch Structure|structure]] element
# Create an {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure|Arch Structure]]}} element.
# Switch to the [[Sketcher Workbench]]
# Switch to the [[Image:Workbench_Sketcher.svg|16px]] [[Sketcher Workbench|Sketcher Workbench]].
# Select one face of the structural element
# Select one face of the structural element.
# Press the {{KEY|[[Image:Sketcher NewSketch.png|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face
# Press the {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face.
# Draw the diagram of your bar
# Draw the diagram of your bar.
# Press the {{KEY|[[Image:Sketcher LeaveSketch.png|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish
# Press the {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish.
⚫
# Switch back to the [[Arch Workbench]]
⚫
# Switch back to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]].
# Select the sketch you just drew
# Select the sketch you just drew.
# Press the {{KEY|[[Image:Arch Rebar.png|16px]] [[Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys
# Press the {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar|Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys.
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element)
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).

Latest revision as of 09:35, 16 June 2020

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Arch Rebar)
# Switch to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]]
# Create an {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure|Arch Structure]]}} element.
# Switch to the [[Image:Workbench_Sketcher.svg|16px]] [[Sketcher Workbench|Sketcher Workbench]].
# Select one face of the structural element.
# Press the {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face.
# Draw the diagram of your bar.
# Press the {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish.
# Switch back to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]].
# Select the sketch you just drew.
# Press the {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar|Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys.
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
  1. Switch to the Arch Workbench
  2. Create an Arch Structure element.
  3. Switch to the Sketcher Workbench.
  4. Select one face of the structural element.
  5. Press the New Sketch button to start a new sketch on the selected face.
  6. Draw the diagram of your bar.
  7. Press the Leave Sketch button to finish.
  8. Switch back to the Arch Workbench.
  9. Select the sketch you just drew.
  10. Press the Arch Rebar button, or press R then B keys.
  11. Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
Retrieved from "http://wiki.freecad.org/index.php?title=Translations:Arch_Rebar/7/en&oldid=710940"