Difference between revisions of "Translations:Arch Rebar/7/en"

From FreeCAD Documentation
Jump to navigation Jump to search
(Importing a new version from external source)
 
(Importing a new version from external source)
Line 1: Line 1:
−
# Create a [[Arch Structure|structure]] element
+
# Create an {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure]]}} element.
−
# Switch to the [[Sketcher Workbench]]
+
# Switch to the [[Sketcher Workbench]].
−
# Select one face of the structural element
+
# Select one face of the structural element.
−
# Press the {{KEY|[[Image:Sketcher NewSketch.png|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face
+
# Press the {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face.
−
# Draw the diagram of your bar
+
# Draw the diagram of your bar.
−
# Press the {{KEY|[[Image:Sketcher LeaveSketch.png|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish
+
# Press the {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish.
−
# Switch back to the [[Arch Workbench]]
+
# Switch back to the [[Arch Workbench]].
−
# Select the sketch you just drew
+
# Select the sketch you just drew.
−
# Press the {{KEY|[[Image:Arch Rebar.png|16px]] [[Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys
+
# Press the {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys.
−
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element)
+
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).

Revision as of 16:32, 9 February 2019

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Arch Rebar)
# Switch to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]]
# Create an {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure|Arch Structure]]}} element.
# Switch to the [[Image:Workbench_Sketcher.svg|16px]] [[Sketcher Workbench|Sketcher Workbench]].
# Select one face of the structural element.
# Press the {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face.
# Draw the diagram of your bar.
# Press the {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish.
# Switch back to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]].
# Select the sketch you just drew.
# Press the {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar|Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys.
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
Translation# Create an {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure]]}} element.
# Switch to the [[Sketcher Workbench]].
# Select one face of the structural element.
# Press the {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face.
# Draw the diagram of your bar.
# Press the {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish.
# Switch back to the [[Arch Workbench]].
# Select the sketch you just drew.
# Press the {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys.
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
  1. Create an Arch Structure.svg Arch Structure element.
  2. Switch to the Sketcher Workbench.
  3. Select one face of the structural element.
  4. Press the Sketcher NewSketch.svg New Sketch button to start a new sketch on the selected face.
  5. Draw the diagram of your bar.
  6. Press the Sketcher LeaveSketch.svg Leave Sketch button to finish.
  7. Switch back to the Arch Workbench.
  8. Select the sketch you just drew.
  9. Press the Arch Rebar.svg Arch Rebar button, or press R then B keys.
  10. Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
Retrieved from "http://wiki.freecadweb.org/index.php?title=Translations:Arch_Rebar/7/en&oldid=414162"