Sketcher CreatePolyline/ru: Difference between revisions

From FreeCAD Documentation
(Created page with "Полилиния всегда начинается с отрезка прямой линии: щелчок - перемещение мыши - щелчок. Перемест...")
No edit summary
Line 8: Line 8:
|Name/ru=Sketcher Полилиния
|Name/ru=Sketcher Полилиния
|Workbenches=[[Sketcher Workbench/ru|Sketcher]]
|Workbenches=[[Sketcher Workbench/ru|Sketcher]]
|MenuLocation=Эскиз → Геометрия эскиза → Создать полилинию
|MenuLocation=Эскиз → Геометрия эскиза → Полилиния
|SeeAlso=[[Sketcher CreateLine/ru|Sketcher Line]]}}
|SeeAlso=[[Sketcher CreateLine/ru|Sketcher Line]]}}



Revision as of 04:07, 30 August 2019

Sketcher Полилиния

Системное название
Sketcher Полилиния
Расположение в меню
Эскиз → Геометрия эскиза → Полилиния
Верстаки
Sketcher
Быстрые клавиши
Нет
Представлено в версии
-
См. также
Sketcher Line

Описание

Этот инструмент работает как инструмент Линия, но создает непрерывные отрезки линии и дуги, соединенные их вершинами. При запуске инструмента указатель мыши меняется на белый крест с красным значком ломаной линии. Координаты указателя отображаются рядом с ним синим цветом в режиме реального времени.

Полилиния начиналась с линии, продолжилась дугой, перпендикулярно к ней следующей дугой, а затем ,по касательной, закончилась линией

Как использовать

Полилиния всегда начинается с отрезка прямой линии: щелчок - перемещение мыши - щелчок. Переместите мышь снова. После размещения первого сегмента линии инструмент Sketcher-а полилиния имеет несколько режимов, которые можно переключать с помощью клавиши M. Например, вы можете нарисовать касательные или перпендикулярные дуги, следующие за линией или сегментом дуги. Повторное нажатие клавиши M переключает следующие режимы:

  1. Press the M key: the new segment is a line which is perpendicular to the previous segment.
  2. Press the M key again: the new segment is a line which is tangential to the previous segment.
  3. Press the M key again: the new segment is an arc which is tangential to the previous segment.
  4. Press the M key again: the new segment is an arc which is perpendicular (left) to the previous segment.
  5. Press the M key again: the new segment is an arc which is perpendicular(right) to the previous segment.
  6. Press the M key again: You are again in the state where you started; the line is only connected with a coincidence to the previous segment.
  • v0.18 and above While in any of the arc modes, holding down the Ctrl key (MacOS: CMD key) and moving the cursor causes the arc to snap by increments of 45 degrees, relative to the previously created polyline segment.
  • Pick points on an empty area of the 3D view, or on an existing object (auto constraints must be active in TaskView).
  • Pressing Esc or clicking the right mouse button before closing the polyline to a loop ends the current polyline and you can continue with a new one. Pressing Esc or clicking the right mouse button again ends the polyline function.
  • Pressing Esc or clicking the right mouse button after closing the polyline to a loop ends the polyline function.