Sketcher CreateFillet: Difference between revisions

From FreeCAD Documentation
(Switch to numbering for consistency with other Usage descriptions)
No edit summary
 
(54 intermediate revisions by 4 users not shown)
Line 1: Line 1:
<languages/>
<languages/>
{{Page_in_progress}}
<translate>
<translate>

<!--T:8-->
<!--T:8-->
{{Docnav
{{Docnav
|[[Sketcher_CreateArcSlot|Arc slot]]
|[[Sketcher_CreateSlot|Slot]]
|[[Sketcher_CreateChamfer|Chamfer]]
|[[Sketcher_Trimming|Trimming]]
|[[Sketcher_Workbench|Sketcher]]
|[[Sketcher_Workbench|Sketcher]]
|IconL=Sketcher_CreateSlot.svg
|IconL=Sketcher_CreateArcSlot.svg
|IconR=Sketcher_Trimming.svg
|IconR=Sketcher_CreateChamfer.svg
|IconC=Workbench_Sketcher.svg
|IconC=Workbench_Sketcher.svg
}}
}}
Line 16: Line 18:
|MenuLocation=Sketch → Sketcher geometries → Create fillet
|MenuLocation=Sketch → Sketcher geometries → Create fillet
|Workbenches=[[Sketcher_Workbench|Sketcher]]
|Workbenches=[[Sketcher_Workbench|Sketcher]]
|Shortcut=F
|Shortcut={{KEY|G}} {{KEY|F}} {{KEY|F}}
|SeeAlso=
|SeeAlso=
}}
}}
Line 23: Line 25:


<!--T:3-->
<!--T:3-->
This tool creates a fillet between two lines joined at one point. Activate the tool, then select both lines or click on the corner point.
The [[Image:Sketcher_CreateFillet.svg|24px]] [[Sketcher_CreateFillet|Sketcher CreateFillet]] tool creates a fillet between two non-parallel edges. {{Version|0.22}}: The tool can also create a chamfer.


{{Version|0.22}}: If two straight edges connected by a [[Sketcher_ConstrainCoincident|Coincident constraint]] are filleted or chamfered, the corner point can optionally be preserved by adding a [[Sketcher_CreatePoint|Point object]] that has a [[Sketcher_ConstrainPointOnObject|Point onto object constraint]] with both edges. Constraints connected to the corner point are then transferred to the new point object.
<!--T:4-->
When starting the tool, the mouse pointer changes to a white cross with a red fillet icon. It stays active so you can do multiple fillets.


</translate>
</translate>
Line 33: Line 34:


==Usage== <!--T:5-->
==Usage== <!--T:5-->

See also: [[Sketcher_Workbench#Drawing_aids|Drawing aids]].


<!--T:6-->
<!--T:6-->
# There are several ways to invoke the tool:
# Press the {{Button|[[File:Sketcher_CreateFillet.svg|16px]] [[Sketcher_CreateFillet|CreateFillet]]}} button.
#* Press the {{Button|[[Image:Sketcher_CreateFillet.svg|16px]] [[Sketcher_CreateFillet|Create fillet]]}} button.
# Pick a vertex connecting two lines; or click on two connected lines, the distance you click from the vertex will set the fillet radius.
#* Select the {{MenuCommand|Sketcher → Sketcher geometries → [[Image:Sketcher_CreateFillet.svg|16px]] Create fillet}} option from the menu.
# Pressing {{KEY|Esc}} or clicking the right mouse button cancels or terminates the function.
#* Right-click in the [[3D_view|3D view]] and select the {{MenuCommand|[[Image:Sketcher_CreateFillet.svg|16px]] Create fillet}} option from the context menu.
#* Use the keyboard shortcut: {{KEY|G}} then {{KEY|F}}, then {{KEY|F}}.
# If there is a previous selection it is cleared. The tool does not accept a pre-selection.
# The cursor changes to a white cross with the current tool mode icon.
# The '''Fillet/Chamfer parameters''' section ({{Version|0.22}}) is added at the top of the [[Sketcher_Dialog|Sketcher Dialog]].
# Optionally press the {{KEY|U}} key or uncheck the '''Preserve corner''' checkbox to disable that option. {{Version|0.22}}
# Optionally press the {{KEY|M}} key or select from the dropdown list in the parameters section to change the tool mode:
#* [[Image:Sketcher_CreateFillet.svg|16px]] '''Fillet'''
#* [[Image:Sketcher_CreateChamfer.svg|16px]] '''Chamfer'''
# Do one of the following:
#* Pick a point with a [[Sketcher_ConstrainCoincident|Coincident constraint]] connecting two non-parallel straight edges.
#* Pick two non-parallel edges. Either edge can be a straight [[Sketcher_CreateLine|line]], an [[Sketcher_CreateArc|arc]], an [[Sketcher_CreateArcOfEllipse|arc of ellipse]], an [[Sketcher_CreateArcOfHyperbola|arc of hyperbola]] or an [[Sketcher_CreateArcOfParabola|arc of parabola]]. [[Sketcher_Workbench#Sketcher_CompCreateBSpline|B-splines]] are currently not supported.
# The fillet or chamfer is created, including a point object in case of a preserved corner. For a chamfer a construction geometry arc is also created.
# This tool always runs in continue mode: optionally keep selecting points and/or edges.
# To finish, right-click or press {{KEY|Esc}}, or start another geometry or constraint creation tool.

== Notes ==

* The construction geometry arc of a chamfer is not visible outside the sketch. It cannot be deleted without breaking the geometry of the chamfer.
* Some ([[Sketcher_Workbench#Sketcher_CompCreateConic|conic]]) curves may need to be [[Sketcher Trimming|trimmed]] before they can be filleted.
* If a [[Sketcher_ConstrainCoincident|Coincident constraint]] connecting two non-parallel straight edges is selected, the fillet radius is derived from the length of the shortest edge.
* If two edges are selected the radius is the distance from the first clicked point to the (extended) intersection of the edges.




<!--T:9-->
<!--T:9-->
{{Docnav
{{Docnav
|[[Sketcher_CreateArcSlot|Arc slot]]
|[[Sketcher_CreateSlot|Slot]]
|[[Sketcher_CreateChamfer|Chamfer]]
|[[Sketcher_Trimming|Trimming]]
|[[Sketcher_Workbench|Sketcher]]
|[[Sketcher_Workbench|Sketcher]]
|IconL=Sketcher_CreateSlot.svg
|IconL=Sketcher_CreateArcSlot.svg
|IconR=Sketcher_Trimming.svg
|IconR=Sketcher_CreateChamfer.svg
|IconC=Workbench_Sketcher.svg
|IconC=Workbench_Sketcher.svg
}}
}}



</translate>
</translate>
{{Sketcher Tools navi{{#translation:}}}}
{{Sketcher_Tools_navi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}
{{clear}}

Latest revision as of 15:37, 24 March 2024

This documentation is a work in progress. Please don't mark it as translatable since it will change in the next hours and days.

Sketcher CreateFillet

Menu location
Sketch → Sketcher geometries → Create fillet
Workbenches
Sketcher
Default shortcut
G F F
Introduced in version
-
See also
None

Description

The Sketcher CreateFillet tool creates a fillet between two non-parallel edges. introduced in version 0.22: The tool can also create a chamfer.

introduced in version 0.22: If two straight edges connected by a Coincident constraint are filleted or chamfered, the corner point can optionally be preserved by adding a Point object that has a Point onto object constraint with both edges. Constraints connected to the corner point are then transferred to the new point object.

Usage

See also: Drawing aids.

  1. There are several ways to invoke the tool:
    • Press the Create fillet button.
    • Select the Sketcher → Sketcher geometries → Create fillet option from the menu.
    • Right-click in the 3D view and select the Create fillet option from the context menu.
    • Use the keyboard shortcut: G then F, then F.
  2. If there is a previous selection it is cleared. The tool does not accept a pre-selection.
  3. The cursor changes to a white cross with the current tool mode icon.
  4. The Fillet/Chamfer parameters section (introduced in version 0.22) is added at the top of the Sketcher Dialog.
  5. Optionally press the U key or uncheck the Preserve corner checkbox to disable that option. introduced in version 0.22
  6. Optionally press the M key or select from the dropdown list in the parameters section to change the tool mode:
    • Fillet
    • Chamfer
  7. Do one of the following:
  8. The fillet or chamfer is created, including a point object in case of a preserved corner. For a chamfer a construction geometry arc is also created.
  9. This tool always runs in continue mode: optionally keep selecting points and/or edges.
  10. To finish, right-click or press Esc, or start another geometry or constraint creation tool.

Notes

  • The construction geometry arc of a chamfer is not visible outside the sketch. It cannot be deleted without breaking the geometry of the chamfer.
  • Some (conic) curves may need to be trimmed before they can be filleted.
  • If a Coincident constraint connecting two non-parallel straight edges is selected, the fillet radius is derived from the length of the shortest edge.
  • If two edges are selected the radius is the distance from the first clicked point to the (extended) intersection of the edges.