Sketcher ConstrainSymmetric/ru: Difference between revisions

From FreeCAD Documentation
(Created page with "{{Userdocnavi/ru}}")
(Updating to match new version of source page)
Line 14: Line 14:
Ограничение симметричности требует от двух выделенных точек быть симметричными относительно данной линии, то есть от обеих точек требуется лежать на нормали к линии через обе точки на одинаковом расстоянии от линии. Альтернативно, она может наложить ограничение на две точки быть симметричными относительно третьей.
Ограничение симметричности требует от двух выделенных точек быть симметричными относительно данной линии, то есть от обеих точек требуется лежать на нормали к линии через обе точки на одинаковом расстоянии от линии. Альтернативно, она может наложить ограничение на две точки быть симметричными относительно третьей.


<div class="mw-translate-fuzzy">
==Действие==
==Действие==
[[File:SymmetricConstraint1.png|256px]]<br /><br />
[[File:SymmetricConstraint1.png|256px]]<br /><br />
Line 22: Line 23:
[[File:SymmetricConstraint3.png|256px]]<br /><br />
[[File:SymmetricConstraint3.png|256px]]<br /><br />
Это ограничение геометрическое и не имеет редактируемых параметров.
Это ограничение геометрическое и не имеет редактируемых параметров.
</div>

[[File:SymmetricConstraint1.png|256px]]

Select two points (vertexes) in the sketch and a line in the sketch. The selected points and the line will be dark green.

[[File:SymmetricConstraint2.png|256px]]

Click on the SymmetricalConstraint icon [[File:Constraint_Symmetric.png|16px]] in the Sketcher toolbar or select the Constrain Symmetrical menu item from the Sketcher Constraints sub menu of the Sketcher (or Part Design) menu item.

This will apply the constraint to the selected items.

[[File:SymmetricConstraint3.png|256px]]

{{Emphasis|Note:}} if you want to define a symmetry constraint with respect to a point, the order of the selection is important, depending on if you select the tool at the beginning or at the end.
* If you click the tool first: select the first point, then the symmetry reference point, and finally the second point.
* If you click the tool last: select the first point, then the second point, and finally the symmetry reference point.

See the tracker [https://freecadweb.org/tracker/view.php?id=4144 issue #4144], and [https://forum.freecadweb.org/viewtopic.php?f=3&t=39611 forum thread].


{{Docnav/ru|[[Sketcher_ConstrainEqual/ru|Equal Length]]|
{{Docnav/ru|[[Sketcher_ConstrainEqual/ru|Equal Length]]|

Revision as of 08:47, 25 September 2019

Sketcher ConstrainSymmetric

Системное название
Sketcher ConstrainSymmetric
Расположение в меню
Sketch → Ограничения эскиза → Ограничение симметричности
Верстаки
Sketcher
Быстрые клавиши
S
Представлено в версии
-
См. также
Ограничение параллельности

Описание

Ограничение симметричности требует от двух выделенных точек быть симметричными относительно данной линии, то есть от обеих точек требуется лежать на нормали к линии через обе точки на одинаковом расстоянии от линии. Альтернативно, она может наложить ограничение на две точки быть симметричными относительно третьей.

Действие



Выделите в эскизе две точки (вершины) и линию. Выделенные точки и линия станут тёмно-зелёными.



Кликните на иконке SymmetricalConstraint на панели инструментов Sketcher или выделите меню Constrain Symmetrical в субменю Sketcher Constraints в разделе меню Sketcher (или Part Design). Это назначит ограничения для выделенных элементов.



Это ограничение геометрическое и не имеет редактируемых параметров.

Select two points (vertexes) in the sketch and a line in the sketch. The selected points and the line will be dark green.

Click on the SymmetricalConstraint icon in the Sketcher toolbar or select the Constrain Symmetrical menu item from the Sketcher Constraints sub menu of the Sketcher (or Part Design) menu item.

This will apply the constraint to the selected items.

Note: if you want to define a symmetry constraint with respect to a point, the order of the selection is important, depending on if you select the tool at the beginning or at the end.

  • If you click the tool first: select the first point, then the symmetry reference point, and finally the second point.
  • If you click the tool last: select the first point, then the second point, and finally the symmetry reference point.

See the tracker issue #4144, and forum thread.