Sketcher ConstrainLock/es: Difference between revisions
Renatorivo (talk | contribs) (Created page with "Debido a que FreeCAD aún está en desarrollo - esta herramienta presenta un comportamiento extraño cuando se intenta 'bloquear' cualquier cosa que no sea un punto. Por ejemp...") |
(Updating to match new version of source page) |
||
Line 9: | Line 9: | ||
NOTA: Actualmente se recomienda utilizar esta herramienta exclusivamente en puntos: |
NOTA: Actualmente se recomienda utilizar esta herramienta exclusivamente en puntos: |
||
Owing to the fact that FreeCAD is still under development - this tool exhibits strange behaviour when it attempts to 'lock' anything other than a point. For example (as of V0.12 R4802), when locking a circle by its circumferential line rather than its centre <em>point</em>, a horizontal constraint and a vertical constraint appear in the constraints dialogue, but they are both of value zero and do not appear in the graphics window. |
|||
==Operation== |
|||
==Funcionamiento== |
|||
<ol> |
<ol> |
||
<li> |
<li>Firstly it is necessary to highlight an item you wish to constrain. For reasons alluded-to above it is wise to only highlight a <em>point</em>.<br /> |
||
[[File:LockConstraint1.png|256px]]</li> |
[[File:LockConstraint1.png|256px]]</li> |
||
<li> |
<li> |
||
Highlighting of a drawing item is achieved by moving the mouse over the item and clicking the left-mouse-button. |
|||
El destacado de un elemento de dibujo se logra moviendo el ratón sobre el elemento y pulsando el botón izquierdo del ratón. |
|||
A highlighted item will change colour to green.<br /> |
|||
[[File:LockConstraint2.png|256px]]</li> |
[[File:LockConstraint2.png|256px]]</li> |
||
<li> |
<li> |
||
Once an item is highlighted, left-clicking on the <em>lock</em> constraint serves to lock the highlighted item in-place. This usually manifests as two constraints: a horizontal distance constraint from the drawing axis origin, and a vertical constraint from the drawing axis origin. These are set by default to the current co-ordinates of the point.<br /> |
|||
Una vez que un elemento está destacado, pulsar con el botón izquierdo del ratón en la restricción de <em>bloquear</em> sirve para bloquear el elemento destacado en su ubicación. Esto normalmente se manifiesta como dos restricciones: Una distancia horizontal desde el origen de coordenadas del dibujo, y una restricción vertical desde el origen del sistema de coordenadas. Estas se establecen por defecto para las coordenadas actuales del punto.<br /> |
|||
[[File:LockConstraint3.png|256px]]</li> |
[[File:LockConstraint3.png|256px]]</li> |
||
<li> |
<li> |
||
The vertical and horizontal constraints forming the lock can be edited by double clicking on the appropriate constraint to be edited either in the drawing itself or in the Constraint tab of the Combo View pane. This will open a dialog box to edit the constraint. Clicking on the horizontal constraint component produces:<br /> |
|||
Las restricciones Vertical y Horizontal que forman el bloqueo se pueden editar haciendo doble clic en la restricción apropiada para ser editada ya sea en el dibujo o en la pestaña de restricciones del panel. Esto abrirá un letrero de diálogo para editar la restricción. Pulsar en la componente horizontal de la restricción produce:<br /> |
|||
[[File:LockConstraint4.png|256px]].</li> |
[[File:LockConstraint4.png|256px]].</li> |
||
<li> |
<li>Enter the desired value into the dialog box and click OK.<br /> |
||
[[File:LockConstraint5.png|256px]]</li> |
[[File:LockConstraint5.png|256px]]</li> |
||
<li> |
<li>The new value of the constraint is applied to the drawing.<br /> |
||
[[File:LockConstraint6.png|256px]]</li> |
[[File:LockConstraint6.png|256px]]</li> |
||
<li> |
<li>The vertical constraint may be similarly edited to constrain the point to the desired location.<br /> |
||
[[File:LockConstraint7.png|256px]]</li></ol> |
[[File:LockConstraint7.png|256px]]</li></ol> |
||
Revision as of 18:43, 4 June 2014
Sketcher ConstrainLock |
Ubicación en el Menú |
---|
Croquizador → Restricciones del Croquizador → Bloquear |
Entornos de trabajo |
Croquizador, Diseño de Piezas |
Atajo de teclado por defecto |
Ninguno |
Introducido en versión |
- |
Ver también |
Restricción Coincidente |
"Crea una restricción de bloqueo sobre el elemento seleccionado"
Descripción
Esta restricción trata de restringir completamente cualquier elemento seleccionado.
NOTA: Actualmente se recomienda utilizar esta herramienta exclusivamente en puntos:
Owing to the fact that FreeCAD is still under development - this tool exhibits strange behaviour when it attempts to 'lock' anything other than a point. For example (as of V0.12 R4802), when locking a circle by its circumferential line rather than its centre point, a horizontal constraint and a vertical constraint appear in the constraints dialogue, but they are both of value zero and do not appear in the graphics window.
Operation
- Firstly it is necessary to highlight an item you wish to constrain. For reasons alluded-to above it is wise to only highlight a point.
-
Highlighting of a drawing item is achieved by moving the mouse over the item and clicking the left-mouse-button.
A highlighted item will change colour to green.
-
Once an item is highlighted, left-clicking on the lock constraint serves to lock the highlighted item in-place. This usually manifests as two constraints: a horizontal distance constraint from the drawing axis origin, and a vertical constraint from the drawing axis origin. These are set by default to the current co-ordinates of the point.
-
The vertical and horizontal constraints forming the lock can be edited by double clicking on the appropriate constraint to be edited either in the drawing itself or in the Constraint tab of the Combo View pane. This will open a dialog box to edit the constraint. Clicking on the horizontal constraint component produces:
. - Enter the desired value into the dialog box and click OK.
- The new value of the constraint is applied to the drawing.
- The vertical constraint may be similarly edited to constrain the point to the desired location.