# Constraint InternalAngle

Menyplacering |
---|

Sketch → Sketcher constraints → Constrain angle |

Arbetsbänk(ar) |

Sketcher, PartDesign |

Standard genväg |

A |

Introducerad i version |

- |

Se även |

Constraint Length, Constraint Perpendicular |

## Description

Angle constraint is a datum constraint intended to fix angles in sketch. It is capable of setting slopes of individual lines, angles between lines, angles of intersections of curves, and angle spans of circular arcs.

## Usage

There are four different ways the constraint can be applied:

- to individual lines
- between lines
- to intersections of curves
- to arcs of circles

To apply angle constraint, one should the follow the steps:

- Select one, two or three entities in the sketch. The mode will be chosen depending on the selection.
- Invoke the constraint using several methods:
- Pressing the Constrain angle button in the toolbar.
- Using the A keyboard shortcut. (
**A**is for**A**ngle) - Using the
**Sketch → Sketcher constraints → Constrain angle**form the top menu entry

- A datum edit dialog box pops up.
- Modify the angle if necessary.
**Note:**The angle can be entered as an expression that will be evaluated and the result will be stored. - Click OK

As with any datum constraint, it is possible to change the angle value later by double-clicking the constraint in constraint list or 3d view. Entering a negative value will cause the angle direction to flip.

## Constraint modes

### Line slope angle

**Accepted selection:** line

The constraint sets the polar angle of line's direction. It is the angle between the line and X axis of the sketch.

### Arc span (v0.15)

**Accepted selection:** arc of circle

In this mode, the constraint fixes angular span of a circular arc.

### Between lines

**Accepted selection:** line + line

In this mode, the constraint sets the angle between two lines. It is not required that the lines intersect.

### Between curves at intersection (angle-via-point) (v0.15)

**Accepted selection:** any line/curve + any line/curve + any point

In this mode, angle between two curves is constrained at the point of their intersection. The intersection point can be on curves' extensions. The point should be specified explicitly, since curves typically intersect in more than one point.

For the constraint to work correctly, the point must be on both curves. So, as the constraint is invoked, the point will be automatically constrained onto both curves (helper constraints will be added, if necessary), and the angle between curves will be constrained at the point. These helper constraints are plain regular constraints. They can be added manually, or deleted. There are no helper constraints on the example picture above, because the point selected is already the intersection of curves.

## Scripting

Angle Constraint can be created from macros and from the python console by using the following:

```
# line slope angle
Sketch.addConstraint(Sketcher.Constraint('Angle',iline,angle))
# angular span of arc
Sketch.addConstraint(Sketcher.Constraint('Angle',iarc,angle))
# angle between lines
Sketch.addConstraint(Sketcher.Constraint('Angle',iline1,pointpos1,iline2,pointpos2,angle))
# angle-via-point (no helper constraints are added automatically when from python)
Sketch.addConstraint(Sketcher.Constraint('AngleViaPoint',icurve1,icurve2,geoidpoint,pointpos,angle))
```

where:

`Sketch`

is a sketch object`iline, iline1, iline2`

are integers specifying the lines by their ordinal numbers in`Sketch`

.`pointpos1, pointpos2`

should be 1 for start point and 2 for end point. The choice of endpoints allows to set internal angle (or external), and it affects how the constraint is drawn on the screen.`geoidpoint`

and`pointpos`

in`AngleViaPoint`

are the indexes specifying the point of intersection.`angle`

is the angle value in radians. The angle is counted between tangent vectors in counterclockwise direction. Tangent vectors are pointing from start to end for the lines (or vice versa if ending point is supplied in angle between lines mode), and along counterclockwise direction for circles, arcs and ellipses. Quantity is also accepted as an angle (e.g.`App.Units.Quantity('45 deg')`

)

**The tools:**New sketch, Edit sketch, Leave sketch, View sketch, View section, Map sketch to face, Reorient sketch, Validate sketch, Merge sketches, Mirror sketch

**Sketcher geometries:**Point, Line by 2 point,**Create an arc,**Arc, Arc by 3 Point,**Create a circle**, Circle, Circle by 3 Point,**Create a conic**, Ellipse by center, Ellipse by 3 points, Arc of ellipse, Arc of hyperbola, Arc of parabola,**Create a B-spline**, Create B-spline, Create periodic B-pline, Polyline (multiple-point line), Rectangle,**Create regular polygon**, Triangle, Square, Pentagon, Hexagon, Heptagon, Octagon, Create Regular Polygon, Slot, Fillet, Trimming, Extend, External Geometry, CarbonCopy, Construction Mode

**Sketcher constraints****Geometric constraints**Coincident, Point On Object, Vertical, Horizontal, Parallel, Perpendicular, Tangent, Equal Length, Symmetric, Constrain Block**Dimensional constraints**Lock, Horizontal Distance, Vertical Distance, Distance, Radius, Internal Angle, Snell's Law, Internal Alignment, Toggle reference/driving constraint,

**Sketcher tools**Select solver DOFs, Close Shape, Connect Edges, Select Constraints, Select Origin, Select Vertical Axis, Select Horizontal Axis, Select Redundant Constraints, Select Conflicting Constraints, Select Elements Associated with constraints, Show/Hide internal geometry, Symmetry, Clone, Copy, Move, Rectangular Array, Delete All Geometry, Delete All Constraints

**Sketcher B-spline tools**Show/Hide B-spline degree, Show/Hide B-spline control polygon, Show/Hide B-spline curvature comb, Show/Hide B-spline knot multiplicity, Convert Geometry to B-spline, Increase degree, Increase knot multiplicity, Decrease knot multiplicity

**Sketcher virtual space**Switch Virtual Space

**Installation:**Linux, Windows, Mac;**Getting started****Basics:**About FreeCAD, Workbenches, Preferences, Document structure, Interface Customization, Properties, Mouse Model; Tutorials**Workbenches**: Arch, Draft, FEM, Image, Inspection, Mesh, OpenSCAD, Part, PartDesign, Path, Plot, Points, Raytracing, Reverse Engineering, Robot, Ship, Sketcher, Spreadsheet, Start, Surface workbench, TechDraw, Test Framework, Web

**Scripting:**Introduction to Python, FreeCAD scripting tutorial, FreeCAD Scripting Basics, How to install macros, Gui Command, Units**Modules:**Builtin modules, Workbench creation, Installing more workbenches**Meshes:**Mesh Scripting, Mesh Module**Parts:**The Part Module, Topological data scripting, PythonOCC, Mesh to Part**Coin scenegraph:**The Coin/Inventor scenegraph, Pivy**Qt interface:**PySide, Using the FreeCAD GUI, Dialog creation**Parametric objects:**Scripted objects**Other:**Code snippets, Line drawing function, Embedding FreeCAD, FreeCAD vector math library, Power users hub, Python, Macros, FreeCAD Scripting Basics, Topological data scripting