Difference between revisions of "Sketcher ConstrainAngle/pl"
(Created page with "==Tworzenie skryptów==")
(Created page with "Ograniczenie kąta może być utworzone przez makropolecenie i z konsoli Pyton za pomocą następujących narzędzi:")
|Line 80:||Line 80:|
# line slope angle
# line slope angle
Revision as of 18:15, 25 October 2020
|Lokalizacja w menu|
|Szkicownik → Wiązania szkicownika → Wiązanie kąta|
|Wprowadzono w wersji|
|Szkicownik: Wiązanie odległości, Szkicownik: Wiązanie prostopadłości|
Angle constraint is a datum constraint intended to fix angles in sketch. It is capable of setting slopes of individual lines, angles between lines, angles of intersections of curves, and angle spans of circular arcs.
There are four different ways the constraint can be applied:
- to individual lines
- between lines
- to intersections of curves
- to arcs of circles
To apply angle constraint, one should the follow the steps:
- Select one, two or three entities in the sketch. The mode will be chosen depending on the selection.
- Invoke the constraint using several methods:
- A datum edit dialog box pops up.
- Modify the angle if necessary. Note: The angle can be entered as an expression that will be evaluated and the result will be stored.
As with any datum constraint, it is possible to change the angle value later by double-clicking the constraint in constraint list or 3d view. Entering a negative value will cause the angle direction to flip.
Line slope angle
Accepted selection: line
The constraint sets the polar angle of line's direction. It is the angle between the line and X axis of the sketch.
Arc span (v0.15)
Accepted selection: arc of circle
In this mode, the constraint fixes angular span of a circular arc.
Accepted selection: line + line
In this mode, the constraint sets the angle between two lines. It is not required that the lines intersect.
Between curves at intersection (angle-via-point) (v0.15)
Accepted selection: any line/curve + any line/curve + any point
In this mode, angle between two curves is constrained at the point of their intersection. The intersection point can be on curves' extensions. The point should be specified explicitly, since curves typically intersect in more than one point.
For the constraint to work correctly, the point must be on both curves. So, as the constraint is invoked, the point will be automatically constrained onto both curves (helper constraints will be added, if necessary), and the angle between curves will be constrained at the point. These helper constraints are plain regular constraints. They can be added manually, or deleted. There are no helper constraints on the example picture above, because the point selected is already the intersection of curves.
Ograniczenie kąta może być utworzone przez makropolecenie i z konsoli Pyton za pomocą następujących narzędzi:
# line slope angle Sketch.addConstraint(Sketcher.Constraint('Angle',iline,angle)) # angular span of arc Sketch.addConstraint(Sketcher.Constraint('Angle',iarc,angle)) # angle between lines Sketch.addConstraint(Sketcher.Constraint('Angle',iline1,pointpos1,iline2,pointpos2,angle)) # angle-via-point (no helper constraints are added automatically when from python) Sketch.addConstraint(Sketcher.Constraint('AngleViaPoint',icurve1,icurve2,geoidpoint,pointpos,angle))
Sketchis a sketch object
iline, iline1, iline2are integers specifying the lines by their ordinal numbers in
pointpos1, pointpos2should be 1 for start point and 2 for end point. The choice of endpoints allows to set internal angle (or external), and it affects how the constraint is drawn on the screen.
AngleViaPointare the indexes specifying the point of intersection.
angleis the angle value in radians. The angle is counted between tangent vectors in counterclockwise direction. Tangent vectors are pointing from start to end for the lines (or vice versa if ending point is supplied in angle between lines mode), and along counterclockwise direction for circles, arcs and ellipses. Quantity is also accepted as an angle (e.g.