Sketcher BSplineIncreaseDegree/it

Converti la geometria in B-spline

Aumenta la molteplicità di nodo

Sketcher

Aumenta di grado
Posizione nel menu
Sketch → Strumenti B-spline → Aumenta di grado
Ambiente
Sketcher
Avvio veloce
Nessuno
Introdotto nella versione
0.17
Vedere anche
Crea B-spline

Descrizione

Aumenta il grado della B-spline (vedere: B-spline).

Utilizzo

1. Selezionare un bordo da una B-spline esistente e premere Aumenta di grado.

Example

B-splines are basically a combination of Bézier curves (nicely explained in this and this video).

In this cubic B-spline (degree 3) there are 3 segments, meaning 3 curves are connected at 2 knots.

The degree is indicated by the number in the center. See Show/hide B-spline degree.

B-spline with degree 3 and 2 knots that each have multiplicity 1.

The outer segments each have 2 control points, the inner segment has none to ensure the knots have multiplicity 1. See this page for an explanation about multiplicity.

Increasing the degree to 4 will add control points without changing the shape of the B-spline:

Same B-spline where the degree was changed from 3 to 4. Note that the knot multiplicity has also increased.

From this result you cannot get back to the initial state of the B-spline by decreasing the degree. Some information is lost when the degree of a B-spline is changed. Decreasing the degree back to 3 leads to this:

Same B-spline where the degree was changed back from 4 to 3. Note that the knot multiplicity has increased again. Depending on the B-spline, the algorithm to decrease the degree may add a lot of knots to preserve the shape as has happened here.

Each segment now has 2 control points and each knot is coincident with an additional control point. The knots have C⁰ continuity so that the B-spline will get "corners" if you move a control point. The information of a higher continuity is therefore lost. See this page for an explanation about continuity.

Converti la geometria in B-spline

Aumenta la molteplicità di nodo

Sketcher

Sketcher

• General: Create sketch, Edit sketch, Map sketch to face, Reorient sketch, Validate sketch, Merge sketches, Mirror sketch, Leave sketch, View sketch, View section, Toggle grid, Toggle snap, Configure rendering order, Stop operation

---

• Sketcher geometries: Point, Line, Arc, Arc by 3 points, Circle, Circle by 3 points, Ellipse, Ellipse by 3 points, Arc of ellipse, Arc of hyperbola, Arc of parabola, B-spline by control points, Periodic B-spline by control points, B-spline by knots, Periodic B-spline by knots, Polyline, Rectangle, Centered rectangle, Rounded rectangle, Triangle, Square, Pentagon, Hexagon, Heptagon, Octagon, Regular polygon, Slot, Fillet, Corner-preserving fillet, Trim, Extend, Split, External geometry, Carbon copy, Toggle construction geometry

---

• Sketcher constraints:
  • Geometric constraints: Coincident, Point on object, Vertical, Horizontal, Parallel, Perpendicular, Tangent, Equal, Symmetric, Block
  • Dimensional constraints: Lock, Horizontal distance, Vertical distance, Distance, Radius or weight, Diameter, Auto radius/diameter, Angle, Refraction (Snell's law)
  • Constraint tools: Toggle driving/reference constraint, Activate/deactivate constraint

---

• Sketcher tools: Select unconstrained DoF, Select associated constraints, Select associated geometry, Select redundant constraints, Select conflicting constraints, Show/hide internal geometry, Select origin, Select horizontal axis, Select vertical axis, Symmetry, Clone, Copy, Move, Rectangular array, Remove axes alignment, Delete all geometry, Delete all constraints

---

• Sketcher B-spline tools: Show/hide B-spline degree, Show/hide B-spline control polygon, Show/hide B-spline curvature comb, Show/hide B-spline knot multiplicity, Show/hide B-spline control point weight, Convert geometry to B-spline, Increase B-spline degree, Decrease B-spline degree, Increase knot multiplicity, Decrease knot multiplicity, Insert knot, Join curves

---

• Sketcher virtual space: Switch virtual space

---

• Additional: Sketcher Dialog, Preferences, Sketcher scripting

User documentation

• Getting started
• Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
• Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate

---

• Help: Tutorials, Video tutorials
• Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web

---

• Addons: Addon Manager, External workbenches, Scripting and macros

---

• Hubs: User hub, Power users hub, Developer hub