Pfad Bohrung

From FreeCAD Documentation
Revision as of 08:22, 1 June 2022 by FuzzyBot (talk | contribs) (Updating to match new version of source page)

Path Drilling

Menüeintrag
Path → Drilling
Arbeitsbereich
Path
Standardtastenkürzel
P,D
Eingeführt in Version
-
Siehe auch
Keiner

Beschreibung

The Drilling command generates a drilling Operation in the Job.

Above: Path Drilling operation sample

Usage

  1. There are several ways to invoke the command:
    • Press the Path Drilling button.
    • Select the Path → Drilling option from the menu.
  2. In the Operation section:
    • Select a ToolController.
    • Select a Coolant Mode.
    • Optionally enable and adjust the following:
      • Peck set the Depth.
      • Dwell set the Time in seconds.
      • Extended Depth.
  3. In the Base Geometry section confirm that the list matches the holes that are intended for processing, and adjust add, enable, or disable, as necessary. Holes can be added by selecting the wall faces of the Holes.
  4. In the Depths section check, and if required adjust, the Start Depth and Final Depth.
  5. In the Heights section check, and if required adjust, the Safe Height and the Clearance Height.
  6. Press the OK button to generate the drilling path(s).

Notes

  • When using edges for Base Geometry, always select the bottom edge of the hole.
  • Always verify the tool chosen is the correct diameter for the hole(s) selected.
  • Peck disabled generates (G81 canned drill cycles). Peck enabled generates (G83 canned drill cycles).
  • Dwell enabled is currently unsupported, but is intended to generate (G82 canned drill cycles).

Properties

Note : Not all of these Properties are available in the Task Window Editor. Some are only accessible in the Data tab of the Properties View panel for this Operation.

Base

Note: It is suggested that you do not edit the Placement property of path operations. Rather, move or rotate the Path Job model as needed.

  • DatenPlacement: Overall placement[position and rotation] of the object - with respect to the origin (or origin of parent object container)
    • DatenAngle: Angle in degrees applied to rotation of the object around Axis property value
    • DatenAxis: Axis(one or multiple) around which to rotate the object, set in sub-properties: x, y, z
      • DatenX: x axis value
      • DatenY: y axis value
      • DatenZ: z axis value
    • DatenPosition: Position of the object, set in sub-properties: x, y, z - with respect to the origin (or origin of parent object container)
      • DatenX: x distance value
      • DatenY: y distance value
      • DatenZ: z distance value
  • DatenLabel: User-provided name of the object (UTF-8)
  • DatenDisabled: List of disabled features

Depth

  • DatenClearance Height: The height needed to clear clamps and obstructions
  • DatenFinal Depth: Final Depth of Tool- lowest value in Z
  • DatenSafe Height: The height above which Rapid motions are allowed. (Rapid safety height between locations)
  • DatenStart Depth: Starting depth of Tool - first cut depth in Z

Drill

  • DatenAdd Tip Length: Calculate the tip length and subtract from final depth
  • DatenDwell Enabled: Enable dwell
  • DatenDwell Time: The time to dwell between peck cycles
  • DatenPeck Depth: Incremental Drill depth before retracting to clear chips
  • DatenPeck Enabled: Enable pecking
  • DatenRetract Height: The height where feed starts and height during retract tool when path is finished
  • DatenReturn Level: Controls how tool retracts Default=G98

Path

  • DatenActive: make False, to prevent operation from generating code
  • DatenComment: An optional comment for this Operation
  • DatenUser Label: User assigned label
  • DatenTool Controller: Defines the Tool controller used in the Operation

Rotation (when available)

  • DatenAttempt Inverse Angle: Automatically attempt Inverse Angle if initial rotation is incorrect.
  • DatenB_Axis Error Override: Visually orient B(y) rotations to model (error in FreeCAD rendering).
  • DatenEnable Rotation: Enable rotation to gain access to holes not normal to Z axis.
  • DatenInverse Angle: Inverse the angle of the rotation. Example: change a rotation from -22.5 to 22.5 degrees.
  • DatenReverse Direction: Reverse orientation of Operation by 180 degrees.

Tasks Window Editor Layout

Descriptions for the settings are provided in the Properties list above.

This section is simply a layout map of the settings in the window editor for the Operation.

Base Geometry

  • Add: adds selected element(s) which should be the base(s) for the path(s)
  • Delete: delete the selected item(s) in the Base Geometry list
  • Clear: clear all items in the Base Geometry list

Base Location

  • Add: add an (X,Y) coordinate location to the current drilling operation.
  • Remove: remove the selected location item(s) from the Base Location list
  • Edit: edit the selected location item

Depths

  • Start Depth:
  • Final Depth:

Heights

  • Safe Height:
  • Clearance Height:

Operation

  • Tool Controller:
  • Retract Height:
  • Peck:
  • Peck Depth:
  • Dwell:
  • Dwell Time:
  • Use Tip Length:

Scripting

See also: FreeCAD Scripting Basics.

Example:

#Place code example here.