CAM Adaptive/de

From FreeCAD Documentation
Revision as of 15:02, 28 February 2022 by FuzzyBot (talk | contribs) (Updating to match new version of source page)

Path Adaptive

Menu location
Path → Adaptive
Workbenches
Path
Default shortcut
None
Introduced in version
-
See also
None

Beschreibung

The Adaptive tool uses an adaptive algorithm to create clearing and profiling paths that manage cutter engagement so that engagement and material removal never exceed a maximum value.

Usage

Usage instructions for the Adaptive operation are presented here.

Basic Operation

  1. Press the Adaptive icon, or select the Path Adaptive from the top menu.
  2. Select the tool controller for the Operation from the Tool controller dialogue pop up window, if prompted.
  3. Adjust the operation depths as needed in the Depths tab: Start Depth, Finish Depth, Step Down.
  4. Make adjustments in Heights tab if needed.
  5. Configure settings in the Operations tab:
    1. (See the Properties → Adaptive section below.)
    2. Set the Step Over value as a percentage of the diameter of the Tool.
  6. If you wish to preview the result before accepting the settings, click Apply
  7. Click OK button to confirm and generate paths.
Preliminary Notes About Adaptive Clearing
  • Depending on the size and complexity of the area for the operation, is might be better to not recompute the operation after every property change; rather, consider:
    • deactivate the operation with the Active toggle tool, make your changes to the operation's properties, then click the Active icon again to re-activate the operation - which triggers a recompute internally.
  • The Adaptive operation might contain a few bugs yet to be clearly identified. Please report bugs and issues in the FreeCAD Path/CAM Forum.
  • All tool shapes may not be respected with this operation. Check the FreeCAD forum for further details.
  • Should you choose to run the path simulator in the Path Workbench, it only uses the standard end mill to simulate paths. Therefore, you will not see tool-shape-specific material removal. Material removal is shown using the end mill shape.

Properties

Note : The names of some Properties in this list differ a little from the same settings used in the Task Window Editor.

Adaptive

  • DatenForce Inside-Out: Force plunging into material inside and clearing towards the edges
  • DatenHelix Angle: Helix ramp entry angle (degrees)
  • DatenHelix Cone Angle: Angle (degrees) of conical helix
  • DatenHelix Diameter Limit: Limit helix entry diameter, if limit larger than tool diameter or 0, tool diameter is used
  • DatenKeep Tool Down Ratio: Max length of keep tool down path compared to direct distance between points
  • DatenLift Distance: Lift distance for rapid moves
  • DatenOperation Type: Type of adaptive operation: Clearing or Profiling
  • DatenSide: Side of selected faces that tool should cut: Inside or Outside
  • DatenStep Over: Percent of cutter diameter to step over on each pass
  • DatenStock to Leave: How much stock to leave (i.e. for a separate finishing operation)
  • DatenTolerance: Influences accuracy and performance
  • DatenUse Helix Arcs: Use Arcs (G2) for helix ramp

Base

Note: It is suggested that you do not edit the Placement property of path operations. Rather, move or rotate the Path Job model as needed.

  • DatenPlacement: Overall placement[position and rotation] of the object - with respect to the origin (or origin of parent object container)
    • DatenAngle: Angle in degrees applied to rotation of the object around Axis property value
    • DatenAxis: Axis(one or multiple) around which to rotate the object, set in sub-properties: x, y, z
      • DatenX: x axis value
      • DatenY: y axis value
      • DatenZ: z axis value
    • DatenPosition: Position of the object, set in sub-properties: x, y, z - with respect to the origin (or origin of parent object container)
      • DatenX: x distance value
      • DatenY: y distance value
      • DatenZ: z distance value
  • DatenLabel: User-provided name of the object (UTF-8)

Depth

  • DatenClearance Height: The height needed to clear clamps and obstructions
  • DatenFinal Depth: Final Depth of Tool- lowest value in Z
  • DatenFinish Depth: Maximum material removed on final pass.
  • DatenSafe Height: The above which Rapid motions are allowed.
  • DatenStart Depth: Starting Depth of Tool- first cut depth in Z
  • DatenStep Down: Incremental Step Down of Tool

Path

  • DatenActive: make False, to prevent operation from generating code
  • DatenComment: An optional comment for this Operation
  • DatenTool Controller: Defines the Tool controller used in the Operation
  • DatenUser Label: User assigned label

Tasks Window Editor Layout

Descriptions for these settings are provided in the Properties list above. This section is simply a layout map of the settings in the window editor for the Operation.

Base Geometry

  • Add: adds selected element(s) which should be the base(s) for the path(s)
  • Delete: delete the selected item(s) in the Base Geometry list
  • Clear: clear all items in the Base Geometry list

Depths

  • DatenStart Depth
  • DatenFinal Depth
  • DatenFinish Depth
  • DatenStep Down

Heights

  • DatenSafe Height
  • DatenClearance Height

Operation

  • DatenTool Controller
  • DatenCut Region (Side)
  • DatenOperation Type
  • DatenStep Over Percent
  • DatenAccuracy vs Performance (Tolerance)
  • DatenHelix Ramp Angle
  • DatenHelix Cone Angle
  • DatenHelix Max Diameter (Helix Diameter Limit)
  • DatenLift Distance
  • DatenKeep Tool Down Ratio
  • DatenStock to Leave
  • DatenForce Clearing Inside-Out
  • DatenStop

Resources