DiseñoPieza Pastilla

From FreeCAD Documentation
Revision as of 12:04, 5 November 2019 by Mario52 (talk | contribs) (Created page with "{{Docnav/es |Create a clone |Revolution |PartDesign |IconL=PartDesign Clone.png |IconC=Workben...")

PartDesign_Pad

Ubicación en el Menú
Diseño de Piezas -> Saliente
Entornos de trabajo
Diseño de Piezas, Complete
Atajo de teclado por defecto
Ninguno
Introducido en versión
-
Ver también
Ninguno

Introducción

'Crea un saliente a partir de un croquis seleccionado' - Esta herramienta toma un croquis seleccionado como entrada (el 'croquis de definición'), y crea a partir de él un 'saliente'. Un saliente es esencialmente una extrusión de un croquis. Por ejemplo, si un croquis estuviera formados por dos circunferencias concéntricas, y se utilizase la herramienta Saliente sobre dicho croquis, el resultado sería un cilindro:

The Pad tool extrudes a sketch into a solid in a direction normal to the sketch plane. Starting with v0.17, faces on the solid can also be used.

Sketch (A) shown on the left; end result after pad operation (B) on the right.

v0.16 and below If the selected sketch is mapped to the face of an existing solid or another Part Design feature, the pad will be fused to it.

How to use

  1. Select the sketch to be padded. In v0.17 and above, a face on the existing solid can alternatively be used.
  2. Press the Pad button.
  3. Set the Pad parameters (see next section).
  4. Click OK.

Opciones

Cuando se crea un saliente, el letrero de diálogo de los 'parámetros del saliente' ofrece cinco diferentes formas de especificar la longitud a la cual el saliente se va a extruir

When creating a pad, the Combo view automatically switches to the Tasks pane, showing the Pad parameters dialogue.

Dimension

Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar seleccionando la opción Invertir. Las extrusiones se realizan normales normales al plano de definición del croquis.

Con la opción Simétrico al plano el saliente se extenderá la mitad de la dimensión indicada hacia cada lado del plano de croquis.

No es posible indicar dimensiones negativas. Utiliza en cambio la opción invertir.

Dos dimensiones

Permite introducir una segunda longitud en la cual el saliente debería extenderse en la dirección opuesta (dentro del soporte). De nuevo se puede cambiar seleccionado la opción invertir.

Hasta el último

El saliente se extruirá hasta la última cara del soporte en la dirección de extrusión. Si no existe soporte, se mostrará un mensaje de error.

Hasta el primero

El saliente se extruirá hasta la primera cara del soporte en la dirección de extrusión. Si no existe soporte, se mostrará un mensaje de error.

Hasta la cara

El saliente se extruirá hasta una cara del soporte que puede seleccionarse designándola. Si no existe soporte, no se aceptará ninguna selección.

Type offers five different ways of specifying the length to which the pad will be extruded.

Dimension

Enter a numeric value for the length of the pad. The default direction for extrusion is away (outside of) the support, but it can be changed by ticking the Reversed option. Extrusions occur normal to the defining sketch plane. With the option Symmetric to plane the pad will extend half of the given length to either side of the sketch plane. Negative dimensions are not possible. Use the Reversed option instead.

Two dimensions

This allows to enter a second length in which the pad should extend in the opposite direction (into the support). Again can be changed by ticking the Reversed option.

To last

The pad will extrude up to the last face of the support in the extrusion direction. If there is no support, an error message will appear.

To first

The pad will extrude up to the first face of the support in the extrusion direction. If there is no support, an error message will appear.

Up to face

The pad will extrude up to a face in the support that can be chosen by clicking on it. If there is no support, no selections will be accepted.

Length

Defines the length of the pad. Multiple units can be used independently of the user's units preferences (m, cm, mm, nm, ft or ', in or ").

Symmetric to plane

Tick the checkbox to extend half of the given length to either side of the sketch plane.

Reversed

Reverses the direction of the pad.

Properties

  • DatosRefine: v0.17 and above true or false. Cleans up residual edges left after the operation. This property is initially set according to the user's settings (found in Preferences → Part design → General → Model settings). It can be manually changed afterwards. This property will be saved with the FreeCAD document.

Limitaciones

  • El algoritmo utilizado para Hasta el primero y Hasta el último:
    • Crea una línea a través del centro de gravedad del croquis
    • Encuentra todas las caras del soporte que se cortan por esta línea
    • Selecciona la cara en la que el punto de intersección está más cerca/lejos del croquis
  • Esto significa que la cara que se encuentre podría no siempre ser la que esperas. Si encuentras este problema, utiliza la opción Hasta la cara, y selecciona la cara que deseas.
  • Para el caso particular de extrusión a una superficie cóncava, donde el croquis es más largo que esta superficie, la extrusión fallará. Este es un error sin resolver.
  • No existe limpiado automático, por ejemplo, superficies planas adyacentes en una superficie individual. Puedes corregir esto manualmente en el entorno de Pieza con Refinar forma.
  • Like all Part Design features, Pad creates a solid, thus the sketch must include a closed profile or it will fail with a Failed to validate broken face error. There can be multiple enclosed profiles inside a larger one, provided none intersect each other (for example, a rectangle with two circles inside it).
  • The algorithm used for To First and To Last is:
    • Create a line through the centre of gravity of the sketch
    • Find all faces of the support cut by this line
    • Choose the face where the intersection point is nearest/furthest from the sketch
This means that the face that is found might not always be what you expected. If you run into this problem, use the Up to face type instead, and pick the face you want.
For the very special case of extrusion to a concave surface, where the sketch is larger than this surface, extrusion will fail. This is a unresolved bug.
  • v0.16 and below There is no automatic cleanup, e.g. of adjacent planar surfaces into a single surface. You can fix this manually in the Part workbench with Refine shape (which creates an unlinked, non-parametric solid) or with the Refine shape feature from the OpenSCAD Workbench which creates a parametric feature.