Part Design: Scanalatura

From FreeCAD Documentation
Revision as of 06:48, 18 March 2018 by Normandc (talk | contribs) (Created page with "=== Utilizzo ===")

Scanalatura

Posizione nel menu
PartDesign → Scanalatura
Ambiente
PartDesign, Completo
Avvio veloce
Nessuno
Introdotto nella versione
-
Vedere anche
Rivoluzione

Descrizione

Questo strumento rivoluziona uno schizzo selezionato o un oggetto 2D attorno ad un dato asse, asportando del materiale dall'oggetto di supporto.

Above: sketch (A) is revolved around axis (B); resulting groove on solid (C) is shown right.

Utilizzo

  1. Selezionare uno schizzo mappato su una faccia o un oggetto 2D
  2. Fare clic su Template:KEY/it.

Opzioni

Quando si crea una scanalatura, la finestra di dialogo Parametri Groove offre diversi parametri per specificare come deve essere ruotato il disegno. I parametri di Scanalatura hanno esattamente lo stesso significato che hanno per la funzione di rivoluzione.

Assi

Questa opzione specifica l'asse intorno al quale il disegno deve essere ruotato. Attualmente, in questa finestra, si può selezionare solo l'asse schizzo orizzontale o verticale.

Angolo

Questa opzione specifica l'angolo di rotazione dello schizzo. Per ottenere una scanalatura completa occorre impostare un angolo di 360°. Non è possibile specificare angoli negativi (se è necessario usare l'opzione Invertito) o angoli maggiori di 360°.

Simmetrico al piano

La rivoluzione si estende per metà dell'angolo specificato in entrambe le direzioni rispetto al piano di schizzo.

Invertito

La direzione di rivoluzione viene invertita.

When creating a groove, the Groove parameters dialogue offers several parameters specifying how the sketch should be revolved.

Axis

This option specifies the axis about which the sketch is to be revolved.

  • Vertical sketch axis: selects the vertical sketch axis .
  • Horizontal sketch axis: selects the horizontal sketch axis.
  • Sketch axis: v0.16 and below selects a construction line contained in the sketch used by the Groove. The first construction line created in the sketch will be labelled Sketch axis 0. The drop down list will contain one custom sketch axis for each construction line.
  • Construction line: v0.17 and above selects a construction line contained in the sketch used by the Groove. The drop down list will contain an entry for each construction line. The first construction line created in the sketch will be labelled Construction line 1.
  • Base (X/Y/Z) axis: v0.17 and above selects the X, Y or Z axis of the Body's Origin;
  • Select reference...: v0.17 and above allows selection in the 3D view of an edge on the Body, or a datum line.

Angle

This controls the angle through which the groove is to be formed, e.g. 360° would be a full, contiguous revolution. It is not possible to specify negative angles (use the Reversed option instead) or angles greater than 360° .

Symmetric to plane

If checked, the groove will extend half of the specified angle in both directions from the sketch plane .

Reversed

If checked, the direction of revolution is reversed from default clockwise to counterclockwise .

Properties

Below are properties which can be defined after creation of the feature. Data properties Base and Axis are uneditable .

  • DatiAngle: angle of rotation. See Angle .
  • DatiLabel: label given to the operation, can be changed at convenience.
  • DatiMidplane: true or false. See Symmetric to plane.
  • DatiReversed: true or false. See Reversed.
  • DatiRefine: v0.17 and above true or false. If set to true, cleans the solid from residual edges left by features. See Part RefineShape for more details.