PartDesign Draft/it: Difference between revisions
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
Line 1: | Line 1: | ||
<languages/> |
<languages/> |
||
<div class="mw-translate-fuzzy"> |
<div class="mw-translate-fuzzy"> |
||
{{Docnav/it|[[PartDesign Chamfer/it|Smusso]]|[[PartDesign Thickness/it|Spessore]]|[[PartDesign_Workbench/it|PartDesign]]|IconL=PartDesign_Chamfer.svg|IconC=Workbench_PartDesign.svg|IconR=PartDesign_Thickness.svg}} |
{{Docnav/it|[[PartDesign Chamfer/it|Smusso]]|[[PartDesign Thickness/it|Spessore]]|[[PartDesign_Workbench/it|PartDesign]]|IconL=PartDesign_Chamfer.svg|IconC=Workbench_PartDesign.svg|IconR=PartDesign_Thickness.svg}} |
||
Line 8: | Line 9: | ||
</div> |
</div> |
||
=== Description === |
|||
<div class="mw-translate-fuzzy"> |
|||
=== Descrizione === |
=== Descrizione === |
||
Questo strumento crea uno sformo angolare (inclinazione delle facce) sulle facce selezionate di un oggetto. Nella struttura del progetto viene creata una nuova voce '''Draft'' indipendente, seguita da un numero sequenziale il documento contiene già altri elementi Draft. |
Questo strumento crea uno sformo angolare (inclinazione delle facce) sulle facce selezionate di un oggetto. Nella struttura del progetto viene creata una nuova voce '''Draft'' indipendente, seguita da un numero sequenziale il documento contiene già altri elementi Draft. |
||
</div> |
|||
{| |
|||
| |
|||
[[Image:PartDesign_Draft-01.png|thumb|left|Select one or more faces on the object before starting the tool. Here, 2 faces have been selected.]] |
|||
[[Image:PartDesign_Draft-02.png|thumb|left|Showing Draft Parameter in TaskPanel.]] |
|||
[[Image:PartDesign_Draft-03.png|thumb|left|2 faces have been added, and a 10 deg. draft applied. The bottom plane has remained dimensionally stable, while the draft has made the top plane smaller.]] |
|||
[[Image:PartDesign_Draft-04.png|thumb|left|The Neutral Plane has been changed to the Top Surface. Now, the top plane has stayed dimensionally stable, while the draft has made the bottom plane larger.]] |
|||
[[Image:PartDesign_Draft-05.png|thumb|left|Pull direction is set to the lower right edge, resulting in the draft pulling to the left.]] |
|||
[[Image:PartDesign_Draft-06.png|thumb|left|Checking the Reverse Direction box has applied an inward draft rather than outward.]] |
|||
| |
|||
=== Usage === |
|||
<div class="mw-translate-fuzzy"> |
<div class="mw-translate-fuzzy"> |
||
Line 58: | Line 75: | ||
{{clear}} |
{{clear}} |
||
</div> |
</div> |
||
=== Parameters and Options === |
|||
==== Add Face / Remove Face ==== |
|||
Click Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. |
|||
==== Draft Angle ==== |
|||
Set the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. |
|||
==== Neutral Plane ==== |
|||
Click Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. |
|||
==== Pull Direction ==== |
|||
Click Pull Direction, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable. |
|||
==== Reverse Pull Direction ==== |
|||
Checking Reverse Pull Direction will toggle the draft between positive and negative angles. |
|||
=== Special Cases === |
|||
The Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |
|||
|} |
|||
Revision as of 19:39, 15 September 2021
Sformo |
Posizione nel menu |
---|
PartDesign → Sformo |
Ambiente |
PartDesign |
Avvio veloce |
Nessuno |
Introdotto nella versione |
- |
Vedere anche |
Nessuno |
Description
Descrizione
Questo strumento crea uno sformo angolare (inclinazione delle facce) sulle facce selezionate di un oggetto. Nella struttura del progetto viene creata una nuova voce 'Draft indipendente, seguita da un numero sequenziale il documento contiene già altri elementi Draft.
Usage
Parameters and OptionsAdd Face / Remove FaceClick Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. Draft AngleSet the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. Neutral PlaneClick Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. Pull DirectionClick Pull Direction, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable. Reverse Pull DirectionChecking Reverse Pull Direction will toggle the draft between positive and negative angles. Special CasesThe Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |
- Structure tools: Part, Group
- Helper tools: Create body, Create sketch, Edit sketch, Map sketch to face
- Modeling tools
- Datum tools: Create a datum point, Create a datum line, Create a datum plane, Create a local coordinate system, Create a shape binder, Create a sub-object(s) shape binder, Create a clone
- Additive tools: Pad, Revolution, Additive loft, Additive pipe, Additive helix, Additive box, Additive cylinder, Additive sphere, Additive cone, Additive ellipsoid, Additive torus, Additive prism, Additive wedge
- Subtractive tools: Pocket, Hole, Groove, Subtractive loft, Subtractive pipe, Subtractive helix, Subtractive box, Subtractive cylinder, Subtractive sphere, Subtractive cone, Subtractive ellipsoid, Subtractive torus, Subtractive prism, Subtractive wedge
- Transformation tools: Mirrored, Linear Pattern, Polar Pattern, Create MultiTransform, Scaled
- Dress-up tools: Fillet, Chamfer, Draft, Thickness
- Boolean: Boolean operation
- Extras: Migrate, Sprocket, Involute gear, Shaft design wizard
- Context menu: Set tip, Move object to other body, Move object after other object, Appearance, Color per face
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub