DiseñoPieza Borrador

Chaflán

Espesor

DiseñoPieza

DiseñoPiezas Borrador
Ubicación en el Menú
DiseñoPiezas → Borrador
Entornos de trabajo
DiseñoPiezas
Atajo de teclado por defecto
Ninguno
Introducido en versión
-
Ver también
Ninguno

Descripción

Esta herramienta crea una corriente de aire angular en las caras seleccionadas de un objeto. Se crea una nueva entrada de borrador separada (seguida de un número secuencial si ya existen borradores en el documento) en el árbol de proyecto.

Select one or more faces on the object before starting the tool. Here, 2 faces have been selected. Showing Draft Parameter in TaskPanel. 2 faces have been added, and a 10 deg. draft applied. The bottom plane has remained dimensionally stable, while the draft has made the top plane smaller. The Neutral Plane has been changed to the Top Surface. Now, the top plane has stayed dimensionally stable, while the draft has made the bottom plane larger. Pull direction is set to the lower right edge, resulting in the draft pulling to the left. Checking the Reverse Direction box has applied an inward draft rather than outward.

Usage Select one or more faces on an object, then start the tool either by clicking its icon or going into the menu. In Draft Parameters on the Task panel, set the required parameters and/or options as described below. Click OK to validate. To edit the draft after the function has been validated, either double-click on the Draft label in the tree view, or right-click on it and select Edit Draft. Parameters and Options Add Face / Remove Face Click Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. Draft Angle Set the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. Neutral Plane Click Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. Pull Direction Click Pull Direction, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable. Reverse Pull Direction Checking Reverse Pull Direction will toggle the draft between positive and negative angles. Special Cases The Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer.

Chaflán

Espesor

DiseñoPieza

PartDesign

• Structure tools: Part, Group
• Helper tools: Create body, Create sketch, Edit sketch, Map sketch to face

---

• Modeling tools
  • Datum tools: Create a datum point, Create a datum line, Create a datum plane, Create a local coordinate system, Create a shape binder, Create a sub-object(s) shape binder, Create a clone
  • Additive tools: Pad, Revolution, Additive loft, Additive pipe, Additive helix, Additive box, Additive cylinder, Additive sphere, Additive cone, Additive ellipsoid, Additive torus, Additive prism, Additive wedge
  • Subtractive tools: Pocket, Hole, Groove, Subtractive loft, Subtractive pipe, Subtractive helix, Subtractive box, Subtractive cylinder, Subtractive sphere, Subtractive cone, Subtractive ellipsoid, Subtractive torus, Subtractive prism, ‎Subtractive wedge

---

• Transformation tools: Mirrored, Linear Pattern, Polar Pattern, Create MultiTransform, Scaled
• Dress-up tools: Fillet, Chamfer, Draft, Thickness
• Boolean: Boolean operation

---

• Extras: Migrate, Sprocket, Involute gear, Shaft design wizard
• Context menu: Set tip, Move object to other body, Move object after other object, Appearance, Color per face

User documentation

• Getting started
• Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
• Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate

---

• Help: Tutorials, Video tutorials
• Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web

---

• Addons: Addon Manager, External workbenches, Scripting and macros

---

• Hubs: User hub, Power users hub, Developer hub