Draft Move/sv

From FreeCAD Documentation
Revision as of 08:52, 16 June 2021 by FuzzyBot (talk | contribs) (Updating to match new version of source page)
Jump to navigation Jump to search
Other languages:
Deutsch • ‎English • ‎Türkçe • ‎español • ‎français • ‎italiano • ‎polski • ‎português do Brasil • ‎română • ‎svenska • ‎čeština • ‎русский

Draft Move.svg Draft Move

Draft -> Move
Draft, Arch
Standard genväg
Introducerad i version
Se även


Detta verktyg flyttar de markerade objekten från en punkt till en annan. Om inget objekt är valt, så kommer du ombes att välja ett.

The command can be used on 2D objects created with the Draft Workbench or Sketcher Workbench, but also on many 3D objects such as those created with the Part Workbench, PartDesign Workbench or Arch Workbench.

Draft Move example.jpg

Moving an object from one point to another


See also: Draft Snap and Draft Constrain.

  • Markera punkter i ett tomt område i 3d vyn, eller på ett existerande objekt.
  • Nedtryckning av CTRL kommer att snäppa din punkt till tillgängliga snäpp-punkter.
  • Nedtryckning av SKIFT kommer att begränsa dig vertikalt eller horisontellt i relation till startpunkten.
  • Om du trycker på ESC så avbryts funktionen.
  • Skriv in siffror för att manuellt mata in en koordinat.
  • C växlar kopieringsläget på/av. Med kopiering på, så kommer objekt(en) att kopieras istället för att flyttas.
  • Nedtryckning av ALT kommer att skapa en kopia, även om kopieringsknappen är av.
  • Om ALT är nedtryckt, så kan du göra multipla kopior ända tills ALT släpps.


The single character keyboard shortcuts mentioned here can be changed. See Draft Preferences.

  • To manually enter coordinates enter the X, Y and Z component, and press Enter after each. Or you can press the Draft AddPoint.svg Enter point button when you have the desired values. It is advisable to move the pointer out of the 3D view before entering coordinates.
  • To use polar coordinates enter a value for the Length and a value for the Angle, and press Enter after each.
  • Check the Angle checkbox to constrain the pointer to the specified angle.
  • Press R or click the Relative checkbox to toggle relative mode. If relative mode is on, the coordinates of the second point are relative to the first point, else they are relative to the coordinate system origin.
  • Press G or click the Global checkbox to toggle global mode. If global mode is on, coordinates are relative to the global coordinate system, else they are relative to the working plane coordinate system. introduced in version 0.20
  • Press T or click the Continue checkbox to toggle continue mode. If continue mode is on, the command will restart after finishing. This mode really only makes sense if copy mode is switched on. Depending on the Select base objects after copying preference, either the original objects are selected for the next command call or the copies that were created last. See Preferences.
  • Press P or click the Copy checkbox to toggle copy mode. If copy mode is on, the command will create moved copies instead of moving the original objects.
  • Press D or click the Modify subelements checkbox to toggle subelement mode. If subelement mode is on, the command will use the selected subelements instead of the whole objects. The subelements must belong to Draft Lines or Draft Wires.
  • If copy mode and subelement mode are both on, and edges of Draft Wires are selected, new wires will be created from those edges.
  • Press Esc or the Close button to abort the command.


  • An Object that is attached cannot be moved with the Draft Move command. To move it either its DataSupport object has to be moved, or its DataAttachment Offset has to be changed.


See also: Preferences Editor and Draft Preferences.

  • To change the number of decimals used for the input of coordinates, lengths and angles: Edit → Preferences... → General → Units → Units settings → Number of decimals.
  • To store and reuse the same copy mode setting across commands: Edit → Preferences... → Draft → General settings → Draft tools options → Global copy mode.
  • To reselect the base objects after copying objects: Edit → Preferences... → Draft → General settings → Draft tools options → Select base objects after copying.


See also: Autogenerated API documentation and FreeCAD Scripting Basics.

To move objects use the move method of the Draft module.

moved_list = move(objectslist, vector, copy=False)
  • objectslist contains the objects to be moved. It is either a single object or a list of objects.
  • vector is the displacement.
  • If copy is True copies are created instead of moving the original objects.
  • moved_list is returned with the original moved objects, or with the new copies. It is either a single object or a list of objects, depending on objectslist.


import FreeCAD as App
import Draft

doc = App.newDocument()

polygon1 = Draft.make_polygon(5, radius=1000)
polygon2 = Draft.make_polygon(3, radius=500)
polygon3 = Draft.make_polygon(6, radius=220)

Draft.move(polygon1, App.Vector(500, 500, 0))
Draft.move(polygon1, App.Vector(500, 500, 0))
Draft.move(polygon2, App.Vector(1000, -1000, 0))
Draft.move(polygon3, App.Vector(-500, -500, 0))

list1 = [polygon1, polygon2, polygon3]

vector = App.Vector(-2000, -2000, 0)
list2 = Draft.move(list1, vector, copy=True)
list3 = Draft.move(list1, -2*vector, copy=True)