Draft Constrain/sv: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
<languages/>
<languages/>
{{Docnav
|[[Draft Coordinates|Coordinates]]
|[[Draft Snap|Snapping]]
|[[Draft_Module|Draft_Module]]
|IconC=Workbench_Draft.svg
}}

<div class="mw-translate-fuzzy">
För att använda begränsning, tryck på {{KEY|SKIFT}} medan du ritar.
För att använda begränsning, tryck på {{KEY|SKIFT}} medan du ritar.
</div>


'''However''', when these parameters need to be precise, it is possible to enter the exact [[Draft Coordinates]] in the dialog for the tool.

Another way of selecting more precise points is by constraining the movement of the pointer to a particular X, Y, or Z direction.

== Horizontal and vertical constraints ==

{{TOCright}}
[[Image:Draft_Constrain_example.jpg]]
[[Image:Draft_Constrain_example.jpg]]
{{Caption|Perpendicular lines that were created by constraining the position of the points orthogonally}}

Hold the {{KEY|Shift}} key while drawing to force the next point to be constrained horizontally (X direction) or vertically (Y direction) in relation to the last point entered. The horizontal or vertical orientation depends on the position of the pointer when you press {{KEY|Shift}}; if you are more east or west from the last point, it will be horizontal; if you are more north or south, it will be vertical. To change the orientation, just release {{KEY|Shift}}, move the pointer to a new location, and hold {{KEY|Shift}} again.

Some tools like [[Draft Offset]] and [[Draft Trimex]] use constraining differently. They do not constrain vertically or horizontally but use a different method more adapted to the particular tool, for example, constraining the operation to a certain line segment.

While constraining the movement of the pointer, the Taskview panel will lock the coordinate values that are not being modified. For example, if using a horizontal constraint, only the X value changes, while the Y and Z values remain at their original relative or absolute coordinates, depending on whether relative mode is active or not.

[[Image:Draft_Constrain_Shift_Taskview_example.png]]
{{Caption|Taskview when using a horizontal constraint while holding the Shift key}}

== X, Y, Z constraints ==

Press one of the {{KEY|X}}, {{KEY|Y}} or {{KEY|Z}} keys after a point to constrain the next point on the specified X, Y, or Z direction. Press the same key again to release the constraint.


Pressing {{KEY|X}} or {{KEY|Y}} is equivalent to holding {{KEY|Shift}} and constraining horizontally or vertically, respectively.
I alla verktyg som stöder begränsning, så kan du tvinga nästa punkt att begränsas horisontellt eller vertikalt i relation till den sist inmatade punkten. Den vertikala eller horisontella begränsningen beror på var musmarkören är när du trycker på {{KEY|SKIFT}}. Om du är norr eller söder om den sista punkten, så kommer begränsningen att bli vertikal. Om du är mer åt öster eller väster, så kommer den att bli horisontal. för att ändra, släpp {{KEY|SKIFT}} och tryck ned igen när musmarkören har en annan position.


[[Image:Draft_Constrain_Y_Taskview_example.png]]
En del verktyg, som [[Draft_Offset/sv|offset]] och [[Draft_Trimex/sv|trimex]] använder begränsning på ett annorlunda sätt. De begränsar inte vertikalt eller horisontellt utan använder ett annat sätt som är mer anpassat för just det verktyget, som till exempel att begränsa operationen till ett visst polyline segment.
{{Caption|Taskview when using a vertical constraint after pressing the Y key}}


<div class="mw-translate-fuzzy">
[[Category:User Documentation/sv]]
[[Category:User Documentation/sv]]
</div>


{{Draft Tools navi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}
{{clear}}
{{clear}}

Revision as of 17:55, 21 February 2020

Other languages:

För att använda begränsning, tryck på SKIFT medan du ritar.

However, when these parameters need to be precise, it is possible to enter the exact Draft Coordinates in the dialog for the tool.

Another way of selecting more precise points is by constraining the movement of the pointer to a particular X, Y, or Z direction.

Horizontal and vertical constraints

Perpendicular lines that were created by constraining the position of the points orthogonally

Hold the Shift key while drawing to force the next point to be constrained horizontally (X direction) or vertically (Y direction) in relation to the last point entered. The horizontal or vertical orientation depends on the position of the pointer when you press Shift; if you are more east or west from the last point, it will be horizontal; if you are more north or south, it will be vertical. To change the orientation, just release Shift, move the pointer to a new location, and hold Shift again.

Some tools like Draft Offset and Draft Trimex use constraining differently. They do not constrain vertically or horizontally but use a different method more adapted to the particular tool, for example, constraining the operation to a certain line segment.

While constraining the movement of the pointer, the Taskview panel will lock the coordinate values that are not being modified. For example, if using a horizontal constraint, only the X value changes, while the Y and Z values remain at their original relative or absolute coordinates, depending on whether relative mode is active or not.

File:Draft Constrain Shift Taskview example.png

Taskview when using a horizontal constraint while holding the Shift key

X, Y, Z constraints

Press one of the X, Y or Z keys after a point to constrain the next point on the specified X, Y, or Z direction. Press the same key again to release the constraint.

Pressing X or Y is equivalent to holding Shift and constraining horizontally or vertically, respectively.

Taskview when using a vertical constraint after pressing the Y key

Draft
User documentation
Retrieved from "http://wiki.freecad.org/index.php?title=Draft_Constrain/sv&oldid=622817"