Draft Circle/sv: Difference between revisions

Revision as of 16:15, 18 June 2014

Menu location
Draft Circle
Draft -> Circle
Workbenches
Draft, Arch
Default shortcut
C I
Introduced in version
-
See also
Draft Arc

Description

The Circle tool creates a circle in the current work plane by entering two points, the center and the radius, or by picking tangents, or any combination of those. It takes the linewidth and color previously set on the Tasks tab. This tool works the same way as the Draft Arc tool, except that it stops after entering the radius.

How to use

Press the Draft Circle button, or press C then I keys
Click a first point on the 3D view, or type a coordinate
Click a second point on the 3D view, or enter a radius value.

Options

The primary use of the circle tool is by picking two points, the centre and a point on the circumference, defining the radius.
By pressing ALT, you can select a tangent instead of picking a point. You can therefore construct several types of circles by selecting one, two or three tangents.
To enter coordinates manually, simply enter the numbers, then press ENTER between each X, Y and Z component.
Press T or click the checkbox to check/uncheck the Continue button. If continue mode is on, the Circle tool will restart after you give the second point, allowing you to draw another circle without pressing the Circle button again.
Press CTRL while drawing to force snapping your point to the nearest snap location, independently of the distance.
Press SHIFT while drawing to constrain your second point horizontally or vertically in relation to the first one.
Press I or the Filled button to have the circle to appear as a face after it has been closed. This simply sets the View->Property of the Circle to "Flat lines" or "Wireframe", so it can easily be changed later.
Press ESC or the Cancel button to abort the current Line command.
The circle can be turned into an arc after creation, by setting its first angle and last angle properties to different values.
Circles, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.

Properties

DataRadius: The radius of the circle
VyPattern: Specifies a hatch pattern to fill the wire with
VyPattern Size: Specifies the size of the hatch pattern

Skriptning

Den skapade cirkeln är ett Del föremå som innehåller en kant med endast ett hörn.

 makeCircle (radius, [placement], [facemode], [startangle], [endangle])

Creates a circle object with given radius.
If a placement is given, it is used.
If facemode is False, the circle is shown as a wireframe, otherwise as a face.
If startangle AND endangle are given (in degrees), they are used and the object appears as an arc.
Returns the newly created object.

Example:

 import Draft
 myCircle = Draft.makeCircle(2)

Other languages:

@@ Line 1: / Line 1: @@
-{{GuiCommand/sv|Name=Draft_Circle|Workbenches=[[Draft Module/sv|Skiss]]|MenuLocation=Drafting → Circle}}
+{{GuiCommand|Name=Draft Circle|Workbenches=[[Draft Module|Draft]], [[Arch Module|Arch]]|MenuLocation=Draft -> Circle|Shortcut=C I|SeeAlso=[[Draft Arc|Draft Arc]]}}
-====Beskrivning====
+==Description==
+The Circle tool creates a circle in the current [[Draft SelectPlane|work plane]] by entering two points, the center and the radius, or by picking tangents, or any combination of those. It takes the [[Draft Linestyle|linewidth and color]] previously set on the Tasks tab. This tool works the same way as the [[Draft Arc]] tool, except that it stops after entering the radius.
-Detta verktyg ritar en cirkel genom att fråga efter två punkter, Centrum och radie, genom att välja tangenter, eller någon kombination av dessa.
 [[Image:Draft_Circle_example.jpg|400px]]
 ==How to use==
-# Press the {{KEY|[[Image:Draft Circle.png|16px]] [[Draft Circle]]}} button, or press {{KEY|C}} then {{KEY|I}} keys
+# Press the {{KEY|[[Image:Draft Circle.png|16px]] [[Draft Circle|Draft Circle]]}} button, or press {{KEY|C}} then {{KEY|I}} keys
 # Click a first point on the 3D view, or type a [[Draft_Coordinates|coordinate]]
 # Click a second point on the 3D view, or enter a radius value.
-====Bruk====
+==Options==
+* The primary use of the circle tool is by picking two points, the centre and a point on the circumference, defining the radius.
+* By pressing {{KEY|ALT}}, you can select a tangent instead of picking a point. You can therefore construct several types of circles by selecting one, two or three tangents.
-* Det primära bruket av cirkelverktyget är att markera två punkter, centrumet och en punkt på omkretsen, vilket definierar radien.
+* To enter coordinates manually, simply enter the numbers, then press {{KEY|ENTER}} between each X, Y and Z component.
-* Om man trycker ned {{KEY|ALT}}, så kan du välja en  tangent istället för att markera en punkt. Du kan därför konstruera flera cirkeltyper genom att välja en, två eller tre tangenter.
+* Press {{KEY|T}} or click the checkbox to check/uncheck the {{KEY|'''Continue'''}} button. If continue mode is on, the Circle tool will restart after you give the second point, allowing you to draw another circle without pressing the Circle button again.
-* Välj en punkt i ett tomt område i 3d vyn, eller på ett existerande objekt.
-* Nedtryckning av {{KEY|CTRL}} kommer att [[Draft_Snap/sv|snäppa]] din punkt till tillgängliga snäpp-punkter.
+* Press {{KEY|CTRL}} while drawing to force [[Draft_Snap|snapping]] your point to the nearest snap location, independently of the distance.
-* Nedtryckning av {{KEY|SKIFT}} [[Draft_Constrain/sv|begränsar]] din nya punkt i relation till föregående punkt.
+* Press {{KEY|SHIFT}} while drawing to [[Draft_Constrain|constrain]] your second point horizontally or vertically in relation to the first one.
+* Press {{KEY|I}} or the {{KEY|'''Filled'''}} button to have the circle to appear as a face after it has been closed. This simply sets the View->Property of the Circle to "Flat lines" or "Wireframe", so it can easily be changed later.
-* Skriv in siffror för att [[Draft_Coordinates/sv|manuellt mata in en koordinat]].
+* Press {{KEY|ESC}} or the {{KEY|'''Cancel'''}} button to abort the current Line command.
-* Om du trycker på {{KEY|ESC}} så avbryts funktionen.
+* The circle can be turned into an arc after creation, by setting its first angle and last angle properties to different values.
-* Den skapade cirkeln kommer att ha nuvarande [[Draft_Linestyle/sv|linjestil]].
+* Circles, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.
 ==Properties==