Arch Site/de: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 52: Line 52:
* {{PropertyData|Extrusion Vector}}: An extrusion vector to use when performing boolean operations
* {{PropertyData|Extrusion Vector}}: An extrusion vector to use when performing boolean operations
* {{PropertyData|Remove Splitter}}: Remove splitters from the resulting shape
* {{PropertyData|Remove Splitter}}: Remove splitters from the resulting shape
* {{PropertyData|North Deviation}}: The angle between the true North and the north direction in this document
* {{PropertyData|Declination}}: The angle between the true North and the North direction in this document, that is, the Y axis.{{version|0.18}} This means that by default (declination of 0 degrees) North points to the Y axis, and East to the X axis. This property was previously known as {{PropertyData|North Deviation}}.


=== View ===
=== View ===
Line 76: Line 76:
== Solar diagram ==
== Solar diagram ==


If [http://pysolar.org/ pysolar] is installed on your system, [[Arch Site]]s can display a solar diagram. For this, {{PropertyData|Longitude}}, {{PropertyData|Latitude}} and {{PropertyData|NorthDeviation}} properties must be correctly set, and {{PropertyView|SolarDiagram}} view property turned on. {{Version|0.17}}
If [http://pysolar.org/ pysolar] is installed on your system, [[Arch Site|Arch Sites]] can display a solar diagram. For this, {{PropertyData|Longitude}}, {{PropertyData|Latitude}} and {{PropertyData|Declination}} (previously {{PropertyData|North Deviation}}) must be correctly set, and {{PropertyView|Solar Diagram}} set to {{TRUE}}. {{Version|0.17}}


[[Image:Freecad-solar-diagram.jpg]]
[[Image:Freecad-solar-diagram.jpg]]
Line 102: Line 102:
FreeCAD.ActiveDocument.recompute()
FreeCAD.ActiveDocument.recompute()


Site = Arch.makeSite(Wall)
Building = Arch.makeBuilding([Wall])
Site = Arch.makeSite([Building])

FreeCAD.ActiveDocument.recompute()
FreeCAD.ActiveDocument.recompute()
FreeCAD.Gui.ActiveDocument.ActiveView.viewIsometric()
}}
}}


=== Solar diagram ===
=== Solar diagram ===


As long as the {{incode|pysolar}} module is present, a solar diagram can be added to the site. Set the longitude, latitude and declination angles as appropriate, as well as an adequate scale for the size of your model.
FreeCAD can add a solar diagram to the active document if the {{incode|Pysolar}} (or {{incode|pysolar}}?) module is available. This module only works with Python3.

Please note that modern versions of {{incode|pysolar}} only work with Python 3.
{{Code|code=
Site.Longitude = -46.38
Site.Latitude = -23.33
Site.Declination = 30
#Site.Compass = True

Site.ViewObject.SolarDiagram = True
Site.ViewObject.SolarDiagramScale = 10000
FreeCAD.ActiveDocument.recompute()
}}

=== Solar diagram independent of Site ===


A solar diagram can be created with the following function
A solar diagram can be created with the following function, independently of any site.
{{Code|code=
{{Code|code=
Node = makeSolarDiagram(longitude, latitude, scale=1, complete=False)
Node = makeSolarDiagram(longitude, latitude, scale=1, complete=False)
Line 116: Line 133:


* Creates a solar diagram as a Pivy node, using {{incode|longitude}} and {{incode|latitude}}, with an optional {{incode|scale}}.
* Creates a solar diagram as a Pivy node, using {{incode|longitude}} and {{incode|latitude}}, with an optional {{incode|scale}}.
* If {{incode|complete}} is {{incode|True}}, the 12 months are drawn.
* If {{incode|complete}} is {{incode|True}}, the 12 months are drawn, which shows the full solar [https://en.wikipedia.org/wiki/Analemma analemma].


{{Code|code=
{{Code|code=
import FreeCADGui, Arch
import FreeCADGui, Arch


Node = Arch.makeSolarDiagram(-46.38, -23.33)
Node = Arch.makeSolarDiagram(-46.38, -23.33, scale=10000, complete=True)
FreeCADGui.ActiveDocument.ActiveView.getSceneGraph().addChild(Node)
FreeCAD.Gui.ActiveDocument.ActiveView.getSceneGraph().addChild(Node)
}}
}}
<div class="mw-translate-fuzzy">
<div class="mw-translate-fuzzy">

Revision as of 08:04, 6 May 2019

Baugrund

Menüeintrag
Architektur → Grundstück
Arbeitsbereich
Arch
Standardtastenkürzel
S I
Eingeführt in Version
-
Siehe auch
Etage, Gebäude

Beschreibung

Der Baugrund ist ein spezielles Objekt, das Eigenschaften eines Standard-FreeCAD-Group-Objekts und Arch-Objekten kombiniert. Es ist besonders zur Repräsentation einer gesamten Projektfläche bzw. eines Terrains geeignet. In IFC-basierter architektonischer Arbeit dient es der Organisation des CAD-Modells und enthält Gebäude-Objekte. Der Baugrund wird auch verwendet, um vorhandenes Gelände zu verwalten und anzuzeigen und kann benutzt werden, um das Volumen von aufzufüllender oder abzutragender Erde zu berechnen.

Anwendung

  1. Selektieren Sie optional ein oder mehrere Objekte, welche in den neuen Baugrund übernommen werden sollen.
  2. Drücken Sie die Schaltfläche Baugrund oder die Tasten S, dann I.

Optionen

  • Nach Anlegen des Baugrunds können diesem ein oder mehrere Objekte durch Ziehen in die Baumansicht oder mittels Hinzufügen-Werkzeug hinzugefügt werden.
  • Durch Ziehen von Objekten aus der Baumansicht oder mittels Entfernen-Werkzeug können Objekte vom Baugrund entfernt werden.

Eigenschaften

Data

  • DatenTerrain: The base terrain of this site
  • DatenAddress: The street and housenumber of this site
  • DatenPostal Code: The postal or zip code of this site
  • DatenCity: The city of this site
  • DatenCountry: The country of this site
  • DatenLatitude: The latitude of this site
  • DatenLongitude: The longitude of this site
  • DatenUrl: An url that shows this site in a mapping website
  • DatenProjected Area: The area of the projection of this object onto the XY plane
  • DatenPerimeter: The perimeter length of this terrain
  • DatenAddition Volume: The volume of earth to be added to this terrain
  • DatenSubtraction Volume: The volume of earth to be removed from this terrain
  • DatenExtrusion Vector: An extrusion vector to use when performing boolean operations
  • DatenRemove Splitter: Remove splitters from the resulting shape
  • DatenDeclination: The angle between the true North and the North direction in this document, that is, the Y axis.introduced in version 0.18 This means that by default (declination of 0 degrees) North points to the Y axis, and East to the X axis. This property was previously known as DatenNorth Deviation.

View

  • AnsichtSolar Diagram: Shows or hides the solar diagram
  • AnsichtSolar Diagram Color: The color of the solar diagram
  • AnsichtSolar Diagram Position: The position of the solar diagram
  • AnsichtSolar Diagram Scale: The scale of the solar diagram

Typical workflow

Start by creating an object that represents your terrain. It must be an open surface, not a solid. For example, it is easy to import mesh data, that can be turned into a Part Shape from menu Part → Create Shape from Mesh. Then, create a Site object, and set its DatenTerrain property to the Part we just created:

Create some volumes (they must be solids) that represent the areas that you wish to be excavated or filled. Double-click the Site object in the Tree View, and add these volumes to the Additions or Subtractions groups. Click OK.

The site geometry will be recomputed and the areas, perimeter, and volumes properties recalculated.

Solar diagram

If pysolar is installed on your system, Arch Sites can display a solar diagram. For this, DatenLongitude, DatenLatitude and DatenDeclination (previously DatenNorth Deviation) must be correctly set, and AnsichtSolar Diagram set to true. introduced in version 0.17

Scripting

Siehe auch: Arch API und FreeCAD Scripting Basics.

Das Baugrund-Werkzeug kann in Makros ebenso wie aus der Python-Konsole heraus über folgende Funktion angesprochen werden:

Site = makeSite(objectslist=None, baseobj=None, name="Site")
erzeugt einen Baugrund inklusive der in der Liste angegebenen Objekte

Beispiel:

import FreeCAD, Draft, Arch

p1 = FreeCAD.Vector(0, 0, 0)
p2 = FreeCAD.Vector(2000, 0, 0)
baseline = Draft.makeLine(p1, p2)
Wall = Arch.makeWall(baseline, length=None, width=150, height=2000)
FreeCAD.ActiveDocument.recompute()

Building = Arch.makeBuilding([Wall])
Site = Arch.makeSite([Building])

FreeCAD.ActiveDocument.recompute()
FreeCAD.Gui.ActiveDocument.ActiveView.viewIsometric()

Solar diagram

As long as the pysolar module is present, a solar diagram can be added to the site. Set the longitude, latitude and declination angles as appropriate, as well as an adequate scale for the size of your model.

Please note that modern versions of pysolar only work with Python 3.

Site.Longitude = -46.38
Site.Latitude = -23.33
Site.Declination = 30
#Site.Compass = True

Site.ViewObject.SolarDiagram = True
Site.ViewObject.SolarDiagramScale = 10000
FreeCAD.ActiveDocument.recompute()

Solar diagram independent of Site

A solar diagram can be created with the following function, independently of any site.

Node = makeSolarDiagram(longitude, latitude, scale=1, complete=False)
  • Creates a solar diagram as a Pivy node, using longitude and latitude, with an optional scale.
  • If complete is True, the 12 months are drawn, which shows the full solar analemma.
import FreeCADGui, Arch

Node = Arch.makeSolarDiagram(-46.38, -23.33, scale=10000, complete=True)
FreeCAD.Gui.ActiveDocument.ActiveView.getSceneGraph().addChild(Node)