Reinforcement LShapeRebar/it: Difference between revisions

From FreeCAD Documentation
(Created page with "== Proprietà ==")
(Created page with "* {{PropertyData|Orientation}}: Decide l'orientamento dell'armatura (es. verso il basso, verso l'alto, a destra o a sinistra). * {{PropertyData|Front Cover}}: La distanza tra...")
Line 23: Line 23:
== Proprietà ==
== Proprietà ==


* {{PropertyData|Orientation}}: It decides the orientation of the rebar (like a bottom, top, right and left).
* {{PropertyData|Orientation}}: Decide l'orientamento dell'armatura (es. verso il basso, verso l'alto, a destra o a sinistra).
* {{PropertyData|Front Cover}}: The distance between rebar and selected face.
* {{PropertyData|Front Cover}}: La distanza tra l'armatura e la faccia selezionata. Copriferro anteriore
* {{PropertyData|Right Cover}}: The distance between the right end of the rebar to right face of the structure.
* {{PropertyData|Right Cover}}: La distanza tra l'estremità destra della barra di destra e la faccia destra della struttura. Copriferro destro
* {{PropertyData|Left Cover}}: The distance between the left end of the rebar to the left face of the structure.
* {{PropertyData|Left Cover}}: La distanza tra l'estremità sinistra della barra di sinistra e la faccia sinistra della struttura. Copriferro sinistro
* {{PropertyData|Bottom Cover}}: The distance between rebar from the bottom face of the structure.
* {{PropertyData|Bottom Cover}}: La distanza tra l'armatura e la parte inferiore della struttura. Copriferro inferiore
* {{PropertyData|Top Cover}}: The distance between rebar from the top face of the structure.
* {{PropertyData|Top Cover}}: La distanza tra l'armatura e la parte superiore della struttura. Copriferro superiore
* {{PropertyData|Rounding}}: A rounding value to be applied to the corners of the bars, expressed in times the diameter.
* {{PropertyData|Rounding}}: Il raggio di curvatura da applicare agli angoli delle barre, espresso quantità di diametro delle barre.
* {{PropertyData|Amount}}: The amount of rebars.
* {{PropertyData|Amount}}: La quantità di barre.
* {{PropertyData|Spacing}}: The distance between the axes of each bar.
* {{PropertyData|Spacing}}: La distanza tra gli assi di ogni barra.


==Scripting==
==Scripting==

Revision as of 09:35, 11 February 2018

Armatura a L

Posizione nel menu
Arch → Strumenti armatura
Ambienti
Arch
Avvio veloce
None
Vedere anche
Armatura, Armatura dritta, Armatura a U, Armatura sagomata, Staffe armatura, Armatura elicoidale
 
Questo comando fa parte del Addon Reinforcement, che è possibile installare tramite il menu Strumenti → Addons Manager

Descrizione

Lo strumento Armatura a L consente all'utente di creare una barra di rinforzo piegata a L (un gancio) nell'elemento strutturale.

Utilizzo

  1. Creare un elemento Struttura
  2. Selezionare una qualsiasi faccia della struttura
  3. Selezionare Armatura a L dagli strumenti Armatura
  4. Sul lato sinistro dello schermo appare un pannello delle azioni come il seguente
  5. Selezionare l'orientamento desiderato
  6. Fornire i dati per front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar
  7. Selezionare la modalità di distribuzione per la quantità e per la spaziatura
  8. Se la spaziatura è selezionata, l'utente può anche optare per una spaziatura personalizzata
  9. Cliccare sulla faccia selezionata serve per verificare o modificare la faccia per la distribuzione dell'armatura
  10. Cliccare OK o Apply per generare l'armatura
  11. Cliccare Cancel per uscire dal pannello delle azioni

Proprietà

  • DatiOrientation: Decide l'orientamento dell'armatura (es. verso il basso, verso l'alto, a destra o a sinistra).
  • DatiFront Cover: La distanza tra l'armatura e la faccia selezionata. Copriferro anteriore
  • DatiRight Cover: La distanza tra l'estremità destra della barra di destra e la faccia destra della struttura. Copriferro destro
  • DatiLeft Cover: La distanza tra l'estremità sinistra della barra di sinistra e la faccia sinistra della struttura. Copriferro sinistro
  • DatiBottom Cover: La distanza tra l'armatura e la parte inferiore della struttura. Copriferro inferiore
  • DatiTop Cover: La distanza tra l'armatura e la parte superiore della struttura. Copriferro superiore
  • DatiRounding: Il raggio di curvatura da applicare agli angoli delle barre, espresso quantità di diametro delle barre.
  • DatiAmount: La quantità di barre.
  • DatiSpacing: La distanza tra gli assi di ogni barra.

Scripting

The LShape Rebar tool can by used in macros and from the python console by using the following function:

makeLShapeRebar(FrontCover, BottomCover, LeftCover, RightCover, Diameter, TopCover, Rounding, AmountSpacingCheck, AmountSpacingValue, orientation, Structure, Facename)
  • The LShape Rebar have four different orientations:
    • Bottom Right
    • Bottom Left
    • Top Right
    • Top Left
  • Adds a LShape reinforcing bar object to the given structural object.
  • If no Structure and Facename is given, it will take user selected face as input.
  • Here CoverAlong argument is having type tuple.
  • Returns the new Rebar object.

Example: Creating LShape rebar.

import Arch, LShapeRebar
structure = Arch.makeStructure(length=1000.0, width=1000.0, height=400.0)
structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
rebar = LShapeRebar.makeLShapeRebar(20, 20, 20, 20, 8, 20, 2, True, 10, "Bottom Left", structure, "Face1")

Changing properties of LShape rebar.

import LShapeRebar
LShapeRebar.editLShapeRebar(50, 50, 20, 20, 8, 20, 2, True, 5, "Top Left")