Sketcher ConstrainCoincident

From FreeCAD Documentation
Jump to navigation Jump to search
This page is a translated version of the page Sketcher ConstrainCoincident and the translation is 6% complete.
Outdated translations are marked like this.
Other languages:
Deutsch • ‎English • ‎español • ‎français • ‎italiano • ‎polski • ‎português • ‎português do Brasil • ‎română • ‎svenska • ‎čeština • ‎русский

Constraint PointOnPoint.svg Sketcher ConstrainCoincident

Sketch → Sketcher constraints → Constrain coincident
Standard genväg
Introducerad i version
Se även
Constrain Lock, Constrain Point onto Object


Create a coincident constraint on the selected item

This constraint tool takes two points as its argument and serves to make the two points coincident. (Meaning to make them as-one-point).

In practical terms this constraint tool is useful when there is a break in a profile for example - where two lines end near each other and need to be joined - a coincident constraint on their end-points will close the gap.


As stated above, this tool takes two arguments - both are points.

  1. First, it is necessary to highlight two distinct points. (Note: this will not work if, for example, you attempt to select the start and end point of the same straight line; selecting the start and end points of an arc will produce a closed circle or ellipse but will constrain the location of the seam to be on that point).
  2. Highlighting of a drawing item is achieved by moving the mouse over the item and clicking the left-mouse-button.
  3. It is also possible to highlight all items inside a rectangle by clicking and dragging. When dragging from left to right (with any vertical motion), only the shapes which are entirely contained within the rectangle will be highlighted; in the other direction all shapes which intersect with the selection rectangle will be highlighted. This can be used to select only the vertices without selecting the edges, by dragging a small recangle around some vertices from left to right, as long as there are no edges which are fully contained within the rectangle.
  4. A highlighted item will change its color to green. (This color can be customized in Editing → Preference → Display → Colors → Selection)
  5. Subsequent items can be highlighted by repeating the above procedure(s). Note: it's unnecessary to hold-down any special key like Ctrl to achieve multiple item selection in a drawing.
  6. Once you have two points highlighted, you can invoke the command using several methods:
    • Pressing on the Sketcher ConstrainCoincident.svg Coinstrain coincident constraint button in the toolbar.
    • Using the C keyboard shortcut.
    • Using the Sketch → Sketcher constraints → Constrain coincident entry in the top menu.

Result: the command will cause the two points to become coincident and be replaced by a single point.

Note: In order to make two points coincident, FreeCAD must out of necessity move one (or both) of the original points.

Alternatives to Coincident constraint

The two constrained items of a Coincident constraint must be start point or end point vertices, or center points of arcs, circles or ellipses. Some combinations which are not possible with a coincident constraint can be emulated using other constraints:

  • The Sketcher ConstrainSymmetric.svg Symmetric constraint can be used to place a start point, end point or center point on the midpoint of a straight line.
  • A midpoint-to-midpoint placement of two straight lines can be achieved by creating a new Sketcher CreatePoint.svg Point and using two Sketcher ConstrainSymmetric.svg Symmetric constraints so that it lies on the midpoint of both lines.
  • A vertex can be constrained to lie along an edge using a Sketcher ConstrainPointOnObject.svgPointOnObject constraint. Note that with this constraint, the point can lie anywhere on the full extension of a segment or curve (i.e. also before the start point or beyond the end point).
  • A collinear placement of two straight lines can be obtained by applying a Sketcher ConstrainTangent.svg Tangent constraint to them, or by combining a Sketcher ConstrainPointOnObject.svg PointOnObject constraint and a Sketcher ConstrainParallel.svg Parallel constraint.
  • Two edges can be made identical by using two Sketcher ConstrainCoincident.svg Coincident constraints, one for each pair of extremities.
  • Two circles can be made identical by using a Sketcher ConstrainCoincident.svg Coincident constraint to merge the centers, and applying an Sketcher ConstrainEqual.svg Equal constraint to their edges. For arcs, this will ensure both arcs are part of the same circle, while allowing them to have different start and end points.


The constraint can be created from macros and from the Python console by using the following command:


where :

  • Sketch is a sketch object
  • LineFixed is the number of the line, that will not move by applying the constraint
  • PointOfLineFixed indicates which vertex of LineFixed has to fulfill the constraint
  • LineMoving is the number of the line, that will move by applying the constraint
  • PointOfLineMoving indicates which vertex of LineMoving has to fulfill the constraint

As the names LineFixed and LineMoving indicate, if both constrained vertices are free to move in any direction, the first one (first to be selected in the Gui) will remain fixed and the other one will move. In the presence of existing constraints, however, both edges may move.

The Sketcher scripting page explains the values which can be used for LineFixed, PointOfLineFixed, LineMoving and PointOfLineMoving, and contains further examples on how to create constraints from Python scripts.