PartDesign Groove

From FreeCAD Documentation
Jump to navigation Jump to search
This page is a translated version of the page PartDesign Groove and the translation is 5% complete.
Outdated translations are marked like this.
Other languages:
Deutsch • ‎English • ‎Türkçe • ‎español • ‎français • ‎italiano • ‎polski • ‎português do Brasil • ‎română • ‎čeština • ‎русский
Arrow-left.svg Previous: PartDesign Hole.svg Hole

PartDesign Groove.svg PartDesign Groove

Ubicación en el Menú
PartDesign → Groove
Entornos de trabajo
Diseño de Piezas, Complete
Atajo de teclado por defecto
Introducido en versión
Ver también


Esta herramienta revoluciona un croquis seleccionado o un objeto 2D alrededor de un eje indicado, cortando material del soporte. Por ejemplo, la imagen muestra un corte de muesca que se elimina del eje.

Groove example.png

The Groove tool revolves a selected sketch or profile about a given axis, cutting out material from the support .

PartDesign Groove example.svg

Above: sketch (A) is revolved around axis (B); resulting groove on solid (C) is shown right.


  1. Select the sketch to be revolved.
    A face on the existing solid can alternatively be used. v0.17 and above
    The sketch must be mapped to the planar face of an existing solid or Part Design feature, or an error message will appear. version 0.16 and below
  2. Press the PartDesign Groove.svg Groove button.
  3. Set the Groove parameters (see next section).
  4. Press OK.


Partdesign groove parameters.png

Cuando se crea una ranura, los parámetros del letrero de diálogo de 'ranura' ofrece varios parámetro especificando como debería revolucionarse. Tienen exactamente el mismo significado que para la operación de revolución.

When creating a groove, the Groove parameters dialogue offers several parameters specifying how the sketch should be revolved.

Partdesign groove parameters.png


This option specifies the axis about which the sketch is to be revolved.

  • Vertical sketch axis: selects the vertical sketch axis .
  • Horizontal sketch axis: selects the horizontal sketch axis.
  • Sketch axis: selects a construction line contained in the sketch used by the Groove. The first construction line created in the sketch will be labelled Sketch axis 0. The drop down list will contain one custom sketch axis for each construction line. version 0.16 and below
  • Construction line: selects a construction line contained in the sketch used by the Groove. The drop down list will contain an entry for each construction line. The first construction line created in the sketch will be labelled Construction line 1. v0.17 and above
  • Base (X/Y/Z) axis: selects the X, Y or Z axis of the Body's Origin; v0.17 and above
  • Select reference...: allows selection in the 3D view of an edge on the Body, or a datum line. v0.17 and above


This controls the angle through which the groove is to be formed, e.g. 360° would be a full, contiguous revolution. It is not possible to specify negative angles (use the Reversed option instead) or angles greater than 360° .

Symmetric to plane

If checked, the groove will extend half of the specified angle in both directions from the sketch plane .


If checked, the direction of revolution is reversed from default clockwise to counterclockwise .


Below are properties which can be defined after creation of the feature. Data properties Base and Axis are uneditable .

  • DATOSAngle: angle of rotation. See Angle .
  • DATOSLabel: label given to the operation, can be changed at convenience.
  • DATOSMidplane: true or false. See Symmetric to plane.
  • DATOSReversed: true or false. See Reversed.
  • DATOSRefine: v0.17 and above true or false. If set to true, cleans the solid from residual edges left by features. See Part RefineShape for more details.

Arrow-left.svg Previous: PartDesign Hole.svg Hole