PartDesign Draft/ru
Расположение в меню |
---|
Part Design → Притяжка |
Верстаки |
Part Design |
Быстрые клавиши |
Нет |
Представлено в версии |
- |
См. также |
... |
Description
This tool creates angular draft on the selected faces of an object. A new separate Draft entry (followed by a sequential number if there are already existing drafts in the document) is created in the Project tree.
|
Usage
Parameters and OptionsAdd Face / Remove FaceClick Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. Draft AngleSet the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. Neutral PlaneClick Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. Pull DirectionClick Pull Direction, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable. Reverse Pull DirectionChecking Reverse Pull Direction will toggle the draft between positive and negative angles. Special CasesThe Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |
- Инструменты структуры: Part, Group
- Вспомогательные инструменты: Create body, Create sketch, Edit sketch, Map sketch to face
- Инструменты моделирования
- Инструменты данных: Create a datum point, Create a datum line, Create a datum plane, Create a local coordinate system, Create a shape binder, Create a clone
- Аддитивные инструменты: Pad, Revolution, Additive loft, Additive pipe, Additive box, Additive cone, Additive cylinder, Additive ellipsoid, Additive prism, Additive sphere, Additive torus, Additive wedge
- Субстрактивные инструменты: Pocket, Hole, Groove, Subtractive loft, Subtractive pipe, Subtractive box, Subtractive cone, Subtractive cylinder, Subtractive ellipsoid, Subtractive prism, Subtractive sphere, Subtractive torus, Subtractive wedge
- Инструменты трансформации: Mirrored, Linear Pattern, Polar Pattern, Create MultiTransform
- Отделочные инструменты: Fillet, Chamfer, Draft, Thickness
- Бинарные: Boolean operation
- Дополнительно: Migrate, Shaft design wizard, Involute gear
- Инструменты контекстного меню: Set tip, Move object to other body, Move object after other object

- Установка: Windows, Linux, Mac; Начинающим
- Базовая: О FreeCAD, Верстаки, Настройки, Структура документа, Настройка интерфейса, Свойства, Модель мыши; Учебники
- Верстаки: Arch, Draft, FEM, Image, Inspection, Mesh, OpenSCAD, Part, PartDesign, Path, Plot, Points, Raytracing, Reverse Engineering, Robot, Ship, Sketcher, Spreadsheet, Start, Surface workbench, TechDraw, Test Framework, Web
- Скрипты: Введение в Python, Учебник скриптов FreeCAD, Основы скриптов FreeCAD, Установка макросов, Команды графического интерфейса, Единицы Модули: Создание модулей, Создание верстаков, Добавление верстаков Сетки: Сеточные скрипты, Модуль сеток Детали: Модуль Part, Скрипты топологических данных, PythonOCC, Из Mesh в Part Coin scenegraph: The Coin/Inventor scenegraph, Pivy Интерфейс Qt: PySide, Использование графического интерфейса FreeCAD, Создание диалогов Параметрические объекты: Скриптовые объекты Прочее: Кусочки кода, Функции рисования линий, Встраивание FreeCAD, Библиотека векторной математики FreeCAD, Хаб опытных пользователей, Python, Макросы, Основы скриптов FreeCAD, Topological data scripting