Draft BezCurve
Menyplacering |
---|
Draft -> BezCurve |
Arbetsbänk(ar) |
Draft, Arch |
Standard genväg |
B Z |
Introducerad i version |
- |
Se även |
Ingen |
Beskrivning
The Draft BezCurve tool creates a Bezier Curve, or a piecewise Bezier curve, from several points. It uses the Draft Linestyle set on the Draft Tray.
The BezCurve tool curve uses control points to define the direction of the curve; on the other hand the Draft BSpline tool specifies the exact points through which the curve will go. To create exact circular or elliptical curves, use Draft Arc and Draft Ellipse.
Bezier curve defined by multiple control points
Usage
- Invoke the Draft BezCurve command several ways:
- Press the Draft BezCurve button in Draft toolbar
- Press the B then Z keyboard keys
- Use the Draft → Bezier tools → BezCurve entry in the Draft menu
- Click a first point on the 3D view, or type a coordinate and press the add point button.
- Click additional points on the 3D view, or type a coordinate and press the add point button.
- Press Esc or the Close button, or double-click the last point to complete the edition.
The object is created as a single Bezier curve of degree number_of_points - 1
. It can be transformed to a piecewise wire made of curves of a specified degree by changing its properties.
The curve can be edited by double clicking on the element in the tree view, or by pressing the Draft Edit button. Then you can move the points to a new position, or click add point or remove point and then click on the curve to add or remove points. You can also change the constraint type of each point.
Node constraints
The segment endpoints can be constrained such that adjacent control points are tangent or symmetric to the segments at the endpoint. First, start editing the curve, then pick one of the tools and then pick a point. Click again on the tool to deactivate it, so you can move the point.
- sharp remove constraints on the points so the curve can have sharp corners.
- tangent force adjacent control points to be tangent.
- symmetric force adjacent control points to be tangent and equidistant.
Limitations
- The Points property does not yet appear in the properties list.
- OpenCascade, and thus FreeCAD, does not support Bezier curves of degrees larger than 25. This should not be a problem in practice, as most users would typically use Bezier curves of degrees 3 to 5.
Options
- Press A or the Finish button to finish the curve, leaving it open.
- Press O or the Close button to close the curve, that is, a segment will be added from the last point to the first one to form a face. At least four points, a curve of degree three, are required to form a face.
- Press W or the Wipe button to remove the curve segments already placed, but keep editing the curve from the last point.
- Press U or the Set WP button to adjust the current working plane in the orientation of the last point.
- Press X, Y or Z after a point to constrain the next point on the given axis.
- To enter coordinates manually, simply enter the numbers, then press Enter between each X, Y and Z component.
- Press R or click the checkbox to toggle relative mode. If relative mode is on, the coordinates of the next point are relative to the last one; if not, they are absolute, taken from the origin (0,0,0).
- Press T or click the checkbox to toggle continue mode. If continue mode is on, the BezCurve tool will restart after you finish the curve, allowing you to draw another one without pressing the tool button again.
- Press L or click the checkbox to toggle filled mode. If filled mode is on, a closed wire will create a filled face (DataMake Face
true
); if not, the closed wire will not make a face (DataMake Facefalse
).
- Note: the curve should not be filled if it intersects itself, as it won't create a proper face. If the curve is filled but no shape is visible, manually set DataMake Face to
false
to see the curve.
- Hold Ctrl while drawing to force snapping your point to the nearest snap location, independently of the distance.
- Hold Shift while drawing to constrain your next point horizontally or vertically in relation to the last one.
- Press Ctrl+Z or press the Undo button to undo the last point.
- Press Esc or the Close button to abort the current command; curve segments already placed will remain.
Properties
Data
- DataDegree: specifies the degree of the Bezier curve or the individual segments.
- DataClosed: specifies if the curve is closed or not. If the curve is initially open, this value is
false
; setting it totrue
will draw a segment to close the curve. If the curve is initially closed, this value istrue
; setting it tofalse
will remove the last segment, and make the curve open. - DataMake Face: specifies if the curve makes a face or not. If it is
true
a face is created, otherwise only the perimeter is considered part of the object. This property only works if DataClosed istrue
.
- Note: do not set DataMake Face to
true
if the curve intersects itself, as it won't create a proper face.
- DataContinuity: (read-only) when the curve is closed, indicates the continuity of the curve
[0]
, or[0,0]
. Otherwise it's[]
.
View
- ViewArrow Size: specifies the size of the symbol displayed at the end of the curve.
- ViewArrow Type: specifies the type of symbol displayed at the end of the curve, which can be dot, circle, arrow, and tick.
- ViewEnd Arrow: specifies whether to show a symbol at the last point of the curve, so it can be used as an annotation line.
- ViewPattern: specifies a Draft Pattern with which to fill the face of the closed curve. This property only works if DataMake Face is
true
, and if ViewDisplay Mode is "Flat Lines". - ViewPattern Size: specifies the size of the Draft Pattern.
Skript
The BezCurve tool can be used in macros and from the Python console by using the following function:
BezCurve = makeBezCurve(pointslist, closed=False, placement=None, face=None, support=None, degree=None)
BezCurve = makeBezCurve(Part.Wire, closed=False, placement=None, face=None, support=None, degree=None)
- Creates a
BezCurve
object with the given list of points,pointslist
.- Each point in the list is defined by its
FreeCAD.Vector
, with units in millimeters. - Alternatively, the input can be a
Part.Wire
, from which points are extracted.
- Each point in the list is defined by its
- If
closed
isTrue
, or if the first and last points are identical, the curve is closed. - If a
placement
is given, it is used; otherwise the shape is created at the origin. - If
face
isTrue
, and the wire is closed, the wire will make a face, that is, it will appear filled.
Example:
import FreeCAD, Draft
p1 = FreeCAD.Vector(0, 0, 0)
p2 = FreeCAD.Vector(1000, 1000, 0)
p3 = FreeCAD.Vector(2000, 0, 0)
p4 = FreeCAD.Vector(1500, -2000, 0)
BezCurve1 = Draft.makeBezCurve([p1, p2, p3, p4], closed=True)
BezCurve2 = Draft.makeBezCurve([p4, 1.3*p2, p1, 4.1*p3], closed=True)
BezCurve3 = Draft.makeBezCurve([1.7*p3, 1.5*p4, 2.1*p2, p1], closed=True)
- Basics: Coordinates, Constraining, Snapping (Near, Extension, Parallel, Grid, Endpoint, Midpoint, Perpendicular, Angle, Center, Ortho, Intersection, Special, Dimensions, Working plane)
- Drawing: Line, Wire, Circle, Arc, Ellipse, Polygon, Rectangle, Text, Dimension, BSpline, Point, ShapeString, Facebinder, Bezier Curve, Label
- Modifying: Move, Rotate, Offset, Trimex, Upgrade, Downgrade, Scale, Edit, Wire to BSpline, Add point, Delete point, Shape 2D View, Draft to Sketch, Array, Path Array, Point Array, Clone, Drawing, Mirror, Stretch
- Utilities: Set working plane, Finish line, Close line, Undo line, Toggle construction mode, Toggle continue mode, Apply style, Toggle display mode, Add to group, Select group contents, Toggle snap, Toggle grid, Show snap bar, Heal, Flip Dimension, VisGroup, Slope, AutoGroup, Set Working Plane Proxy, Add to Construction group
- Additional: Preferences, Import-Export Preferences (DXF/DWG, SVG, OCA, DAT); Draft API
- Installation: Windows, Linux, Mac; Getting started
- Basics: About FreeCAD, Workbenches, Preferences, Document structure, Interface Customization, Properties, Mouse Model; Tutorials
- Workbenches: Arch, Draft, FEM, Image, Inspection, Mesh, OpenSCAD, Part, PartDesign, Path, Plot, Points, Raytracing, Reverse Engineering, Robot, Ship, Sketcher, Spreadsheet, Start, Surface workbench, TechDraw, Test Framework, Web
- Scripting: Introduction to Python, FreeCAD scripting tutorial, FreeCAD Scripting Basics, How to install macros, Gui Command, Units Modules: Builtin modules, Workbench creation, Installing more workbenches Meshes: Mesh Scripting, Mesh Module Parts: The Part Module, Topological data scripting, PythonOCC, Mesh to Part Coin scenegraph: The Coin/Inventor scenegraph, Pivy Qt interface: PySide, Using the FreeCAD GUI, Dialog creation Parametric objects: Scripted objects Other: Code snippets, Line drawing function, Embedding FreeCAD, FreeCAD vector math library, Power users hub, Python, Macros, FreeCAD Scripting Basics, Topological data scripting