Arch: Rebar Stirrup

From FreeCAD Documentation
Revision as of 20:06, 23 September 2020 by FuzzyBot (talk | contribs) (Updating to match new version of source page)
Other languages:

Arch Rebar Stirrup

poziția meniului
Arch → Rebar tools
Ateliere
Arch, BIM
scurtătură
nici unul
Prezentat în versiune
0.17
A se vedea, de asemenea,
Helical Rebar, Rebar

Descriere

Instrumentul Stirrup Rebar permite utilizatorului să creeze un 

stirrup reinforcing bar în elementul de structură.

The Stirrup Rebar tool is also integrated into BIM Workbench.

This command is part of the Reinforcement Workbench, an external workbench that can be installed with the Addon Manager via the Tools → Addon manager → Reinforcement menu.

Cum se folosește

  1. Creează un element structure
  2. Select any face of the structure
  3. Then select Stirrup Rebar from the rebar tools
  4. A task panel will pop-out on the left side of the screen as shown below
  5. Select the desired orientation
  6. Give the inputs like left cover, right cover, top cover, bottom, front cover, bent angle, bent factor, rounding and diameter of the rebar
  7. Select the mode of distribution either amount or spacing
  8. If spacing is selected, a user can also opt for custom spacing
  9. Pick selected face is used to verify or change the face for rebar distribution
  10. Click OK or Apply to generate the rebars
  11. Click pe Cancel ieșirea din task panel

Taskview panel for the Arch Rebar Stirrup tool

Proprietăți

  • DateFront Cover: Distanța dintre armături și fațetele selectate.
  • DateRight Cover: Distanța între capătul dintre capătul dreapta al armăturii și fațeta dreapta a structurii.
  • DateLeft Cover: Distanța dintre capătul din stânga al armăturii și fațeta stângă a structurii
  • DateBottom Cover: Distanța dintre armătură și fațeta de jos a structurii.
  • DateTop Cover: Distanța dintre armătură și fața superioară a structurii.
  • DateBent Angle: Bent angle defines the angle at the ends of a stirrup.
  • DateBent Factor: Bent Factor defines length of stirrup end.
  • DateAmount: Cantitatea de armătură
  • DateSpacing: Distanța dintre acele fiecărei bare.

Scrip-Programare

Instrumentul Stirrup Rebar poate fi utilizat în macros și de la consola Python prin utilizarea următoarei funcției: 

Rebar = makeStirrup(l_cover, r_cover, t_cover, b_cover, f_cover,
                    bentAngle, bentFactor, diameter, rounding, amount_spacing_check, amount_spacing_value,
                    structure=None, facename=None)
  • Adds a Stirrup reinforcing bar object to the given structural object.
  • If no Structure and Facename is given, it will take user selected face as input.
  • Here CoverAlong argument is having type tuple.
  • Returns the new Rebar object.

Exemplu: Crearea unei armături tip Stirrup rebar. 

import Draft, Arch, Stirrup

# It doesn't work if the structure is not based on a face
# Structure = Arch.makeStructure(length=1000, width=400, height=400)

Rect = Draft.makeRectangle(400, 400)
Structure = Arch.makeStructure(Rect, height=1600)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

Rebar = Stirrup.makeStirrup(20, 20, 20, 20, 20,
                            115, 4, 8, 2, True, 10, Structure, "Face6")

Schimbarea proprietăților barei Stirrup. 

editStirrup(Rebar, l_cover, r_cover, t_cover, b_cover, f_cover,
            bentAngle, bentFactor, diameter, rounding, amount_spacing_check, amount_spacing_value,
            structure=None, facename=None)
  • Rebar is a previously created StirrupRebar object.
  • The other parameters are the same as required by the makeStirrup() function.
  • structure and facename may be omitted so that the rebar stays in the original structure.
import Stirrup

Stirrup.editStirrup(Rebar, 20, 20, 20, 20, 50,
                    100, 4, 14, 8, True, 8)
Arch
User documentation
Retrieved from "http://wiki.freecad.org/index.php?title=Reinforcement_StirrupRebar/ro&oldid=765834"